Manuals / Brands / Musical Instruments & Equipment / Music Mixer / Telos / Musical Instruments & Equipment / Music Mixer

Telos ZephyrExpress ISDN connections 7: How do I connect ZephyrExpress to an ISDN circuit?

1 186

Download 186 pages, 2.2 Mb

QUICK RESULTS 1-19

hHOT TIP:

Create an Autodial that calls a Master Setup you’ve created for a specific remote

venue. Then go to the Utility: Safe Mode menu and block everything except

Autodialing.

The remote operator can then just press the DIAL button for (virtually) foolproof

remotes.

ISDN connections 7: How do I connect ZephyrExpress to an ISDN circuit?

There are two telephone jacks on the left side of the rear panel. Only one of them should

be connected to the ISDN line.

The upper jack is an S/T interface, for lines that have an NT1 terminator (frequently

supplied by phone companies in Europe). Use the supplied 8-conductor cable, or a

10Base-T (“Category 5”) cable, to the NT1. This jack also provides power to the

terminator.

wNOTE:

ZephyrExpress sold in North America provide power for an external NT1. If

you’re using one of these, disconnect any other power supply connected to

the NT1. If both ZephyrExpress and the NT1 are providing power, both will be

damaged.

You can tell if a ZephyrExpress will supply power by looking at the ISDN

connections: if there are two telephone jacks, it’s a North American unit and

you must follow the above precaution. If there’s only one telephone jack, it’s

a European unit and can be connected safely to powered NT1s.

European units are also marked with a Euro Telecom logo on the

rear panel.

The lower telephone jack on a North American ZephyrExpress is a U interface marked

LINE DIRECT. This is designed for direct connection to the unterminated lines supplied by

American telephone companies. This jack uses ZephyrExpress’ internal NT1. The phone

company may have supplied an 8-pin jack (RJ-45) or a standard four-conductor jack (RJ-

14 or RJ-11); you can plug a standard telephone line cord into either jack and it will work

properly. If the phone company has supplied screw terminals or bare wires, use a

modular cord with spade lugs, available from electronics stores, and connect to red and

green.

The green LED below the LINE DIRECT label will blink rapidly when first contacting the

central office, and then blink slowly while handshaking is going on. When the

connection is complete, the LED will light steadily. If this doesn’t appear to be

happening, see section 9 of this manual for troubleshooting tips.

Contents

Main What youve got here: Customer Service Feedback Test Lines ZephyrExpress will dial a test line for you: e Repairs w e Table of Contents Section 1: Quick Results Section 2: What Youve Got Here... Section 3: ZephyrExpress Hardware Section 4: Audio Operations Page A Note From the President... Page Page xii Introduction Menu Structure Utility Menu SECTION 1: QUICK RESULTS Part I: Instant Gratification, or How to hear stereo music over a phone line 1-2 Part II: Fast Answers to Frequently-Asked Questions 1-15 c Part I: Instant Gratification, or How to hear stereo music over a phone line Gather information about your ISDN line Page Set up the hardware Page Configure ZephyrExpress for your ISDN line. u U T D Call yourself (testing your unit and the line) Configure the Codec u U Set up an audio input and output Place the call to yourself d Page Tune into one of our test lines U d i p Part II: Fast Answers to Frequently-Asked Questions The Basics T 1: What do I do if Im totally lost? l 2: How do I use the menus? u T right. Theres a complete map to the menus in the front of this manual. 3: How do I use a menu that appears locked? 4: How do I lock a specific menu? 5: How do I enter numbers or names? 6: How do I create my own Setups and Master Setups? You can capture a snapshot of all your current settings by using the ISDN connections 7: How do I connect ZephyrExpress to an ISDN circuit? 8: How do I manually enter a network setup? 9: How do I test that Ive set things up properly? p d Alternate test procedure 10: What do I do if I cant connect? Audio setup 11: How do I set ZephyrExpress for my microphones? 12: How do I use line-level sources? 13: How do I create a monitor mix? 14: How do I test my audio and compression setups? ISDN Connection 15: How do I place a call? d 16: What do I do if they cant hear me? 17: How do I send a test tone? 18: How do I hang up? p 19: Where do I find answers to other questions? Page Page ZEPHYREXPRESS HARDWARE 3-1 SECTION 3 ZEPHYREXPRESS HARDWARE About our hardware... 3-2 Front Panel 3-2 Rear Panel 3-10 About our hardware... Front Panel ZEPHYREXPRESS HARDWARE 3-3 The Mixer Section t MIXERS: Send Monitor 1 Monitor 2 Send Mixer Mic 1 and Mic 2 Routing Switches Line 1&2 Routing Switch Monitor Mixers Send Routing Switches Display section Send and Receive Meters Lock LEDs dp l T d p SAFE indicator LCD Display Control section U Edit knob T h DIAL button w ZEPHYREXPRESS HARDWARE 3-9 Numeric Keypad UTIL button u settings. This is fully discussed in Section 7. Rear Panel MODE switches SAFE MODE Software Options ISDN Connections Data connection section S Interface Pinouts i U Interface ZEPHYREXPRESS HARDWARE 3-13 U Interface Pinouts Line Direct LED Remote Control jacks RS-232 RS-232 Pinouts Parallel Port Parallel Port Inputs ZEPHYREXPRESS HARDWARE 3-15 Audio i/o section All XLR Pinouts ZephyrExpress Unbalanced Input5k, audio Microphone Inputs ZEPHYREXPRESS HARDWARE 3-17 Line Inputs 3-conductor input plug 2-conductor input plug Monitor 1 XLR outputs Direct ISDN Receive outputs Power connection ZEPHYREXPRESS HARDWARE 3-19 Power Input Power Supply Power Supply XLR Output w e Page SECTION 4 AUDIO OPERATIONS A console at your fingertips... Mix flexibility The Send Mixer ? Microphone Inputs XLR + Overload LED w Mic Routing Switches Line Inputs Routing Stereo (A B) / Mono (A+B) / off Line A XLR/TRS + Gain t SEND Meters CH A CH B SEND 4-8 AUDIO OPERATIONS The Monitor Mixers Send Routing Level Receive Routing Level Receive Meters Lock Indicators Mon 2 Headphone Jack MONITOR 2 Routing Level Send Routing Level About Monitor Panning Monitor 1 Receive Monitor 1 Send Adjusting individual monitor panning Receive Meters CH A CH B RECEIVE LOCK lights Analog (G.711) phone calls Analog call signal routing Receiving calls w Placing calls d Hanging up p Dealing with Delay Mix-Minus Phones and Remotes REMOTE SITE STUDIO Page SECTION 5 AUDIO CODING OVERVIEW Introduction to Audio Coding Basic Principles of Perceptual Coding Page ISO/MPEG LAYER 3 Layer 3 Features Psychoacoustic Masking Redundancy Reduction 32 bands 576 Bands Bit Reservoir Buffering Ancillary Data Layer 3 Joint Stereo ISO/MPEG LAYER 2 Layer 2 Joint Stereo Layer 2 Mono-128 G.722 CASCADING Mixed MPEG Layer 2 And Layer 3 Signal Chains CHOOSING THE CODING METHOD FOR YOUR APPLICATION Audio Coding Comparison Chart Delay vs. Quality Dual vs Stereo vs Joint Stereo in Layer 3 Dual Site Operation Layer 2: Mono64kpbs vs MONO128; Dual vs JSTEREO Sampling Rate Compatibility Between Telos Codecs With Non-Telos Equipment Page Page SECTION 6 MENU REFERENCE The Menu System 6-2 Using Setups 6-6 Menu Details 6-11 The Menu System A typical menu Navigation Shortcuts Getting HELP ? Menu Overview Utility Menu Using Setups Codec Setup Items Applying a Setup Creating or Changing a Setup You can use Master Setups described on page 7 to change multiple Setups simultaneously. Master Setups Master Setup Menus Applying a Master Setup w Creating or Changing a Master Setup Auto-creating a new Master Setup Manually creating a Master Setup Updating an existing Master Setup Deleting a Master Setup Autodial Setups Creating a new Autodial Editing or deleting an Autodial Menu Details Codec menu Page Normal operation is impossible unless Loop Mode is Off. When this mode is on, The level meters are disabled in Loop Mode: Far, and the middle LED of each is lit as a reminder. Audio menu Page ISDN menu Page System menu h Page Safe mode menu Page SECTION 7 ISDN ISDN BASICS 7-2 HOW TO ORDER ISDN 7-7 ISDN BASICS Background The Basic Rate Interface (BRI) SPIDS Get the SPIDs, Get the SPIDs, GET THE SPIDS! Directory Numbers (DNs) Long-Distance Digital Connectivity HOW TO ORDER ISDN Dealing with The Phone Company Details, Details t ZephyrExpress ISDN Compatibility Protocols Ordering: Central Office Switches and Protocols National ISDN-1 (USA and Canada) AT&T Point-to-Point (Custom) (USA, Japan, Israel, some others) AT&T Point-to-Multipoint (Custom) Northern Telecom DMS100 Functional (Custom, PVC1) (USA, Canada, some others) Euro-ISDN (Europe, Hong Kong, some others) Page SECTION 8 SYSTEM FUNCTIONS Introduction Software Updates New software and upgrade procedures will always be announced at our web site, www.zephyr.com. ZephyrExpress data ports The Serial Port RS-232 Pinouts Communicating c Security Levels t Command Help Command Language Details c Page Page Page The Parallel Port Parallel Port Page SECTION 9 TROUBLESHOOTING First Steps 9-2 GENERAL 9-3 ISDN Problems 9-13 First Steps GENERAL Thinking About Problem Solving Its never just The ISDN isnt working... but how isnt it working? Other Ideas Diagnostic Aids Look into the Lights p d LOOPBACK modes Page Page w Dont forget to set Codec: Loop mode back to Off before attempting normal operation. Some Error Conditions No functionality; the box is totally or partly dead. Condition: ISDN Connecting OK, But No Audio Condition: No Audio In Both Directions Condition: Audio In One Direction Only Condition: Audio Distorted Condition: Major Echo Action Error Messages ISDN Problems Condition: Cant Get ISDN Ready Ready Indication Page i Page Page Intermittent ISDN Problems ISDN Cause Phrases/Values Page Page Page Page Page Page Page SECTION 11 APPENDIX The Faxable ISDN Order Form (for use in US only) 11-15 ABOUT AUDIO LEVELS 11-2 CODEC COMPATIBILITY INFORMATION 11-3 FINDING PUBLIC ISDN SITES 11-7 ABOUT AUDIO LEVELS Nominal Levels Level, Gain, dBu and dBm CODEC COMPATIBILITY INFORMATION Page Comprehensive ZephyrExpress Compatibility List Page FINDING PUBLIC ISDN SITES Page List of Known Working SPIDs by Telephone Company Ameritech Bell Atlantic Bell South Cincinatti Bell ISDN BRI, ZEPHYR, AND YOU Ordering ISDN Dealing with the Phone Company Details, Details Page Page The Faxable ISDN Order Form (for use in US only) FAXABLE ISDN BRI LINE ORDER FORM PROTOCOL: National ISDN-1 PROTOCOL: AT&T Point-to-Point (Custom) PROTOCOL: AT&T Point-to-Multipoint (Custom) PROTOCOL: Northern Telecom DMS100 Functional (Custom, PVC1)