Texas Instruments TMS320C6712D warranty Multichannel Buffered Serial Port Timing

SPRS293 − OCTOBER 2005

MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)

timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 45)

				−150
NO.			MASTER		SLAVE		UNIT
			MIN MAX		MIN	MAX
4	tsu(DRV-CKXH)	Setup time, DR valid before CLKX high	12		2 − 6P		ns
5	th(CKXH-DRV)	Hold time, DR valid after CLKX high	4		5 + 12P		ns

†P = 1/CPU clock frequency in ns. For example, when running parts at 150 MHz, use P = 6.7 ns.

‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.

switching characteristics over recommended operating conditions for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 45)

					−150
NO.		PARAMETER	MASTER§		SLAVE			UNIT
			MIN	MAX	MIN		MAX
1	t	Hold time, FSX low after CLKX high¶	T − 2	T + 3				ns
	h(CKXH-FXL)
2	td(FXL-CKXL)	Delay time, FSX low to CLKX low#	H − 2	H + 3				ns
3	td(CKXL-DXV)	Delay time, CLKX low to DX valid	−3	4	6P + 2 10P		+ 17	ns
6	tdis(CKXH-DXHZ)	Disable time, DX high impedance following last data bit from	H − 2	H + 3				ns
		CLKX high
7	tdis(FXH-DXHZ)	Disable time, DX high impedance following last data bit from FSX			2P + 3	6P	+ 17	ns
		high
8	td(FXL-DXV)	Delay time, FSX low to DX valid			4P + 2	8P	+ 17	ns

†P = 1/CPU clock frequency in ns. For example, when running parts at 150 MHz, use P = 6.7 ns.

‡For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. § S = Sample rate generator input clock = 2P if CLKSM = 1 (P = 1/CPU clock frequency)

=Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)

T =	CLKX period = (1 + CLKGDV) * S
H =	CLKX high pulse width	= (CLKGDV/2 + 1) * S if CLKGDV is even
		= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L =	CLKX low pulse width	= (CLKGDV/2) * S if CLKGDV is even

=(CLKGDV + 1)/2 * S if CLKGDV is odd or zero

¶FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX and FSR is inverted before being used internally.

CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP

#FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock (CLKX).

92 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443