Be sure to set the [Printer Status Monitoring] as shown in the table below. The status monitor has been disabled as default. Wrong setting disables proper printing.

Configuration for the Status Monitor

When the [Printer Status Monitoring] is set to other than “Disabled”, it is possible to monitor the printer status from the host computer. When this feature is not supported or is unnecessary, choose the “Disabled” for the [Printer Status Monitoring]. Doing so reduces the load on the printer driver and increases the print efficiency.

 

 

 

 

 

: Any setting

X: Disabled

 

 

 

Interface

 

 

 

 

 

RS-232C *1

Parallel (Printer cable) *2

USB

LANWLAN

 

(Serial interface

Conforming to IEEE1284

 

10BASE-T100BASE-TX

 

cable)

(Compatible/ECP mode)

 

 

 

 

 

 

Conditions

Other than the right

CENTRO.MODE=ECP

Ver1.1/2.0

Standard TCP/IP

Other Port

Printer model

column

PLUG&PLAY =ON

PortRAW

 

 

 

 

 

 

 

 

 

 

 

 

 

B-SX6T-R

 

X

Not supported

 

 

 

X

B-SX8T-R

 

 

 

 

 

 

 

 

 

 

 

B-EX4T1-G

 

X

Not supported

 

 

 

X

B-EX4T1-T

 

 

 

 

 

 

 

 

 

 

 

B-EX4T2-G

 

 

 

 

 

 

 

B-EX4T2-T

 

X

Not supported

 

 

 

X

B-EX4T2-H

 

 

 

 

 

 

 

B-EV4-G

X

X

Not supported

X

X

 

X

 

 

 

 

 

 

 

 

B-EV4-T

X

X

Not supported

X

X

 

X

 

 

 

 

 

 

 

 

B-EP2DL-G

 

Not supported

Not supported

 

 

 

X

 

 

 

 

 

 

 

 

B-EP4DL-G

Not supported

Not supported

Not supported

 

 

 

X

 

 

 

 

 

 

 

 

B-452-R

 

X

Not supported

 

 

 

X

 

 

 

 

 

 

 

 

B-852-R

 

X

Not supported

 

 

 

X

 

 

 

 

 

 

 

 

B-SA4G, B-SA4G-CN,

 

X

Not supported

 

 

 

X

B-SA4T, B-SA4T-CN

 

 

 

 

 

 

 

 

 

 

 

B-SX4, B-SX4-CN

 

X

 

 

 

X

B-SX5, B-SX5-CN

 

 

 

 

 

 

 

 

 

 

 

B-SV4

 

X

Not supported

 

Not supported

Not

 

 

supported

 

 

 

 

 

 

 

B-372

X

X

Not supported

Not

X

 

X

supported

 

 

 

 

 

 

 

 

B-472

X

X

Not supported

Not

X

 

X

B-472-CN

supported

 

 

 

 

 

 

 

B-572

X

X

Not supported

Not

Not supported

Not

supported

supported

 

 

 

 

 

 

B-672

X

X

Not supported

Not

X

 

X

B-872

supported

 

 

 

 

 

 

 

B-682

X

X

Not supported

Not

X

 

X

B-882

supported

 

 

 

 

 

 

 

B-415

X

Not supported

Not supported

Not

Not supported

Not

supported

supported

 

 

 

 

 

 

B-419

X

Not supported

Not supported

X

Not supported

Not

supported

 

 

 

 

 

 

 

B-431

X

Not supported

Not supported

Not

Not supported

Not

supported

supported

 

 

 

 

 

 

B-452, B-452H

X

X

Not supported

Not

X

 

X

supported

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B-482

X

X

Not supported

Not

X

 

X

supported

 

 

 

 

 

 

 

 

B-492

X

X

Not supported

Not

X

 

X

supported

 

 

 

 

 

 

 

 

B-852

X

X

Not supported

Not

X

 

X

supported

 

 

 

 

 

 

 

 

B-SP2D

X

Not supported

Not supported

Not

X

 

X

supported

 

 

 

 

 

 

 

 

CB-416-T3

X

X

Not supported

Not

Not supported

Not

CB-426-T3

supported

supported

 

 

 

 

 

Notes:

1.When RS-232C (Serial interface) is used for connection, it will take time until printing starts. It is recommended to use other interfaces as far as possible.

-6 -

Page 8
Image 8
Toshiba BDRV-WBX8-Z31 Version 7.2.4 M-3 manual Configuration for the Status Monitor, Interface