Simm Installation | Vanguard Managed Solutions 6500 PLUS specs

Replacing Processor Card Components

Example of SIMM Figure 2-21shows how a SIMM is installed in a slot.

Installation

Insert SIMM into socket at a slight angle.

Figure 2-21. SIMM Installation

2-60	Installation

Image 68

Vanguard Managed Solutions 6500 PLUS installation manual Simm Installation

Contents

Vanguard Managed Solutions Restricted Rights Notification for U.S. Government Users Restricted Rights Legend Proprietary Material Radio Frequency Interference RegulationsPage Contents Contents This Chapter Describes About This ManualOverview Mise en garde Level Chapter Protocols Software FeaturesFeatures Hardware Card TypesProcessor Cards Support Cards Enclosure Enclosures and BackplanesStandalone Supports Other VanguardMSProducts Types of Modulus 6500PLUS Processor Cards Configurations 6525PLUS NetworkConcentrator Port Plus Processor Card Front Panel Hardware 6500PLUS Auxiliary Processor Cards 6500PLUS Asynchronous and Universal I/O Cards AIO CardUIO Card Card Type Works with Port Types Split Speed Plus Universal I/O or Asynchronous I/O Card Front Panel 6500PLUS Network Storage Option Card NSO Card Plus Network Storage Option Card 6500PLUS Token Ring Interface Module Option Token Ring Interface Module Trim Card Hardware 6500PLUS Integral DSU HardwareComponents DSU InterfacePage Installation Overview Chapter Installing Standalone Units UnpackingSite Preparation Example Installation ProcedureStep Action Description/Result Rear View Replacing Processor Cards in Standalone Enclosures Step Action Remove the Standalone Enclosure Door Bottom of Standalone Enclosure Using Screwdriver on Locking Tabs Locking Tabs Replacement Card Plus Processor Card with Retaining Screw Step Action Information Installing Nodes in Modulus EnclosuresAdditional Multiprocessor Nodes MultiprocessorNode Example Operation Replacing Master Processor of Multi-Processor Node Action Result/Description Installing Nodes in Modulus Enclosures Step Action Result/Description When To Add Another Processor with Flash Before You BeginAdding a Secondary 6500PLUS Processor with Flash Select Enable Flash MaintainingCurrent Software Revision Upgrading with Software From the New Processor Card Select Copy Software to Flash Installing/Replacing Processor Cards Modulus 8/18 Requirements for Installing a Trim Card Product Description Code Trim Card Rear Filler Panel for Modulus 8/18 Enclosures Guidelines for Installing a Trim Card in a Modulus 8/18 Trim Card Spacing in a Modulus 18 Enclosure 10. Trim Card Rear Filler Panel for Modulus 9/21 Enclosures Installing Nodes in Modulus Enclosures 11. Trim Card In Left-most Position of Modulus 21 Enclosure Plus Between Two BackplanesEnclosure Installing Nodes in Modulus Enclosures Installing and Connecting a Trim Card Attaching a Trim Card Installing Connecting a Trim Card Attaching Cables Removing/Replacing Trim Cards Before RemovingTrim Cards TRIM/Processor Card Preparing Modulus Enclosures for RFI Suppression Modulus 18 with Installing RFI SuppressionScreen Modulus 18 RFI No Trim Card 15. RFI Suppression Straps Modulus 18 No Trim Card Bar Modulus 21RFI Suppression Ctp CR Starting Up the NodeNode Startup Replacing Processor Card Components Processor Card Replacing DIMs Removal New DIM 19. Jumpers on the Port Interface Pins Jumpers 20. Installing Jumpers on the Port Interface Pins Installing SIMMs Guidelines 21. Simm Installation Replacing Flash Modules 22. Flash Module Installation Replacing ID Modules Module Replacing Prom Chips Chips Replacing the Cmem Chip DSU DIM Installation Installing the DSU Control Terminal Configuring the 6500PLUS for DSU Operation Output Signals DSU Input and Output SignalingInput Signals 24. Diagnostics Menu Loopback Options Troubleshooting DSU DIM Installation Troubleshooting Facility Interface DSU DIM FCC InformationType of Interface DSU DIM Installation Power-Up Verification CheckingLights Event Result/Description Power-Up Diagnostics Setting Node to Default Configuration Node Installing Software Options Accessing Node Serial Number from Node Statistics Access SerialNumber Status/Statistics Select Node Stat 25. Serial Number on Node Stat Screen Enabling a Software Access Key Configure Select Software Key TableFollow These Steps Installing New Software Options in an Existing Network Install New Enhanced LAN Option Appendix a Cables Function/Signal Pin Function/SignalPin Name Position Position Signal Name 35/V.36 Modulus 9/21 EnclosuresFunction Pin Function Signals Modulus 9/21 Enclosures 35/V.36 Signals Standalone and Modulus 8/18 Enclosures Signals Standalone and Modulus 8/18 Enclosures Position Name Pin Function Page Unit Dimensions SpecificationsPhysical Characteristics Limits Power RequirementsEnvironmental Index DIM LL 2-69RS