Chapter | Vanguard Managed Solutions 6500 PLUS specification

Chapter 2

Installation

Overview

Introduction

This chapter contains installation procedures for:

•6500PLUS Series standalone enclosures

•6500PLUS processor card components

•Software options

A description of the processor front panel LED power-up sequence and soft- ware upgrade procedures are also included.

This chapter also contains instructions for installing TRIM cards in Modulus enclosures. For general information on setting up Modulus 8/18 enclosures and inserting 6500PLUS cards into the enclosures, refer to the Modulus Planning and Installation Guide . For Modulus 9/21 enclosures, see the Modulus 9 and 21 Installation and Operation Guide.

Warning etc. The following special notices apply to all equipment handling procedures in this chapter:

Be sure a power outlet is near the equipment and easily accessible.

Warning

Only trained, qualified technicians should perform the installation and replacement procedures in this chapter.

Caution

Ports that are capable of connecting to other apparatus are defined as SELV. To ensure conformity with EN60950 — ensure that these ports are only connected to ports of the same type on other apparatus.

6500PLUS cards, DIMs, SIMMs, and FLASH modules are sensitive to static discharge, which can damage components. Use proper handling and grounding precautions whenever you handle a 6500PLUS card.

Installation

2-19

Image 27

Vanguard Managed Solutions 6500 PLUS installation manual Chapter, Installation Overview

Contents

Vanguard Managed Solutions Restricted Rights Legend Restricted Rights Notification for U.S. Government Users Radio Frequency Interference Regulations Proprietary MaterialPage Contents Contents About This Manual OverviewThis Chapter Describes Level Mise en garde Chapter Software Features FeaturesProtocols Support Cards HardwareCard Types Processor Cards Enclosures and Backplanes StandaloneEnclosure Types of Modulus Supports OtherVanguardMS Products 6500PLUS Processor Cards Port Configurations6525PLUS Network Concentrator Plus Processor Card Front Panel Hardware 6500PLUS Auxiliary Processor Cards Card Type Works with Port Types Split Speed 6500PLUS Asynchronous and Universal I/O CardsAIO Card UIO Card Plus Universal I/O or Asynchronous I/O Card Front Panel NSO Card 6500PLUS Network Storage Option Card Plus Network Storage Option Card Token Ring Interface Module Trim Card 6500PLUS Token Ring Interface Module Option Hardware DSU Interface 6500PLUS Integral DSUHardware ComponentsPage Chapter Installation Overview Example Installing Standalone UnitsUnpacking Site Preparation Rear View InstallationProcedure Step Action Description/Result Step Action Replacing Processor Cards in Standalone Enclosures Remove the Standalone Enclosure Door Bottom of Standalone Enclosure Locking Tabs Using Screwdriver on Locking Tabs Plus Processor Card with Retaining Screw Replacement Card Step Action Installing Nodes in Modulus Enclosures AdditionalInformation Operation Multiprocessor NodesMultiprocessor Node Example Action Result/Description Replacing Master Processor of Multi-Processor Node Installing Nodes in Modulus Enclosures When To Add Another Processor with Flash Before You Begin Adding a Secondary 6500PLUS Processor with FlashStep Action Result/Description Revision Select Enable FlashMaintaining Current Software Select Copy Software to Flash Upgrading with Software From the New Processor Card Modulus 8/18 Installing/Replacing Processor Cards Product Description Code Requirements for Installing a Trim Card Trim Card Rear Filler Panel for Modulus 8/18 Enclosures Guidelines for Installing a Trim Card in a Modulus 8/18 Trim Card Spacing in a Modulus 18 Enclosure 10. Trim Card Rear Filler Panel for Modulus 9/21 Enclosures Installing Nodes in Modulus Enclosures 11. Trim Card In Left-most Position of Modulus 21 Enclosure Between Two Backplanes EnclosurePlus Installing Nodes in Modulus Enclosures Attaching a Trim Card Installing and Connecting a Trim Card Connecting a Trim Card Installing Cables Attaching TRIM/Processor Card Removing/Replacing Trim CardsBefore Removing Trim Cards Modulus 18 with Preparing Modulus Enclosures for RFI Suppression Modulus 18 RFI Installing RFISuppression Screen 15. RFI Suppression Straps Modulus 18 No Trim Card No Trim Card Modulus 21 RFI SuppressionBar Starting Up the Node Node StartupCtp CR Processor Card Replacing Processor Card Components Replacing DIMs New DIM Removal Jumpers 19. Jumpers on the Port Interface Pins 20. Installing Jumpers on the Port Interface Pins Guidelines Installing SIMMs 21. Simm Installation Replacing Flash Modules 22. Flash Module Installation Module Replacing ID Modules Chips Replacing Prom Chips Replacing the Cmem Chip Installing the DSU DSU DIM Installation Control Terminal Configuring the 6500PLUS for DSU Operation DSU Input and Output Signaling Input SignalsOutput Signals Loopback Options 24. Diagnostics Menu Troubleshooting Troubleshooting DSU DIM Installation DSU DIM FCC Information Type of InterfaceFacility Interface DSU DIM Installation Event Result/Description Power-Up VerificationChecking Lights Diagnostics Power-Up Node Setting Node to Default Configuration Installing Software Options Status/Statistics Select Node Stat Accessing Node Serial Number from Node StatisticsAccess Serial Number 25. Serial Number on Node Stat Screen Steps Enabling a Software Access KeyConfigure Select Software Key Table Follow These Install New Installing New Software Options in an Existing Network Enhanced LAN Option Cables Appendix a Name Position Function/Signal PinFunction/Signal Pin Function Position Signal Name35/V.36 Modulus 9/21 Enclosures Function Pin Signals Modulus 9/21 Enclosures 35/V.36 Signals Standalone and Modulus 8/18 Enclosures Position Name Signals Standalone and Modulus 8/18 Enclosures Pin Function Page Specifications Physical CharacteristicsUnit Dimensions Power Requirements EnvironmentalLimits DIM Index LL 2-69RS