Vanguard Managed Solutions 6500 PLUS specification

Hardware

NSO Card	Figure 1-5shows the NSO card.
	TEST (Red)
	Indicates status of internal tests.
	On: Test failed	6500
	Off: Normal condition
	Flashing: Test in progress

MEM (Yellow) Indicates amount of memory available on this card MEM 1: 1 Mbyte RAM

MEM 3: 3 Mbyte RAM

MEM 5: 5 Mbyte RAM

NSO

TEST

MEM1

MEM3

MEM5

DISK

On when disk is being accessed.

P.C. 68908

Figure 1-5. 6500PLUS Network Storage Option Card

1-14	About the 6500PLUS

Image 22

Vanguard Managed Solutions 6500 PLUS installation manual Plus Network Storage Option Card

Contents

Vanguard Managed Solutions Restricted Rights Notification for U.S. Government Users Restricted Rights Legend Proprietary Material Radio Frequency Interference RegulationsPage Contents Contents Overview About This ManualThis Chapter Describes Mise en garde Level Chapter Features Software FeaturesProtocols Processor Cards HardwareCard Types Support Cards Standalone Enclosures and BackplanesEnclosure Products Supports OtherVanguardMS Types of Modulus 6500PLUS Processor Cards Concentrator Configurations6525PLUS Network Port Plus Processor Card Front Panel Hardware 6500PLUS Auxiliary Processor Cards UIO Card 6500PLUS Asynchronous and Universal I/O CardsAIO Card Card Type Works with Port Types Split Speed Plus Universal I/O or Asynchronous I/O Card Front Panel 6500PLUS Network Storage Option Card NSO Card Plus Network Storage Option Card 6500PLUS Token Ring Interface Module Option Token Ring Interface Module Trim Card Hardware Components 6500PLUS Integral DSUHardware DSU InterfacePage Installation Overview Chapter Site Preparation Installing Standalone UnitsUnpacking Example Step Action Description/Result InstallationProcedure Rear View Replacing Processor Cards in Standalone Enclosures Step Action Remove the Standalone Enclosure Door Bottom of Standalone Enclosure Using Screwdriver on Locking Tabs Locking Tabs Replacement Card Plus Processor Card with Retaining Screw Step Action Additional Installing Nodes in Modulus EnclosuresInformation Node Example Multiprocessor NodesMultiprocessor Operation Replacing Master Processor of Multi-Processor Node Action Result/Description Installing Nodes in Modulus Enclosures Adding a Secondary 6500PLUS Processor with Flash When To Add Another Processor with Flash Before You BeginStep Action Result/Description Current Software Select Enable FlashMaintaining Revision Upgrading with Software From the New Processor Card Select Copy Software to Flash Installing/Replacing Processor Cards Modulus 8/18 Requirements for Installing a Trim Card Product Description Code Trim Card Rear Filler Panel for Modulus 8/18 Enclosures Guidelines for Installing a Trim Card in a Modulus 8/18 Trim Card Spacing in a Modulus 18 Enclosure 10. Trim Card Rear Filler Panel for Modulus 9/21 Enclosures Installing Nodes in Modulus Enclosures 11. Trim Card In Left-most Position of Modulus 21 Enclosure Enclosure Between Two BackplanesPlus Installing Nodes in Modulus Enclosures Installing and Connecting a Trim Card Attaching a Trim Card Installing Connecting a Trim Card Attaching Cables Trim Cards Removing/Replacing Trim CardsBefore Removing TRIM/Processor Card Preparing Modulus Enclosures for RFI Suppression Modulus 18 with Screen Installing RFISuppression Modulus 18 RFI No Trim Card 15. RFI Suppression Straps Modulus 18 No Trim Card RFI Suppression Modulus 21Bar Node Startup Starting Up the NodeCtp CR Replacing Processor Card Components Processor Card Replacing DIMs Removal New DIM 19. Jumpers on the Port Interface Pins Jumpers 20. Installing Jumpers on the Port Interface Pins Installing SIMMs Guidelines 21. Simm Installation Replacing Flash Modules 22. Flash Module Installation Replacing ID Modules Module Replacing Prom Chips Chips Replacing the Cmem Chip DSU DIM Installation Installing the DSU Control Terminal Configuring the 6500PLUS for DSU Operation Input Signals DSU Input and Output SignalingOutput Signals 24. Diagnostics Menu Loopback Options Troubleshooting DSU DIM Installation Troubleshooting Type of Interface DSU DIM FCC InformationFacility Interface DSU DIM Installation Lights Power-Up VerificationChecking Event Result/Description Power-Up Diagnostics Setting Node to Default Configuration Node Installing Software Options Number Accessing Node Serial Number from Node StatisticsAccess Serial Status/Statistics Select Node Stat 25. Serial Number on Node Stat Screen Follow These Enabling a Software Access KeyConfigure Select Software Key Table Steps Installing New Software Options in an Existing Network Install New Enhanced LAN Option Appendix a Cables Pin Function/Signal PinFunction/Signal Name Position Function Pin Position Signal Name35/V.36 Modulus 9/21 Enclosures Function Signals Modulus 9/21 Enclosures 35/V.36 Signals Standalone and Modulus 8/18 Enclosures Signals Standalone and Modulus 8/18 Enclosures Position Name Pin Function Page Physical Characteristics SpecificationsUnit Dimensions Environmental Power RequirementsLimits Index DIM LL 2-69RS