Vanguard Managed Solutions 6500 PLUS manual

Installing Nodes in Modulus Enclosures

Modulus 8/18 Nests The TRIM card has its own backplane and attaches to the solder side of the 6500PLUS processor card. The TRIM card requires two Modulus slots. The TRIM filler panel for Modulus 8/18 nests is two slots wide as shown in Figure 2-8.

65xx 18-Port Backplane

Rear View

Attach backplane using a

Phillips-head screwdriver.

Shielded

Twisted Pair

Unshielded

Twisted Pair

TRIM Card

Filler Panel for

Modulus 8/18

Use flat-head screwdriver to attach captive

hardware.

Figure 2-8. TRIM Card Rear Filler Panel for Modulus 8/18 Enclosures

Installation

2-37

Image 45

Vanguard Managed Solutions 6500 PLUS installation manual Trim Card Rear Filler Panel for Modulus 8/18 Enclosures

Contents

Vanguard Managed Solutions Restricted Rights Legend Restricted Rights Notification for U.S. Government Users Radio Frequency Interference Regulations Proprietary MaterialPage Contents Contents About This Manual OverviewThis Chapter Describes Level Mise en garde Chapter Software Features FeaturesProtocols Card Types HardwareProcessor Cards Support Cards Enclosures and Backplanes StandaloneEnclosure VanguardMS Supports OtherProducts Types of Modulus 6500PLUS Processor Cards 6525PLUS Network ConfigurationsConcentrator Port Plus Processor Card Front Panel Hardware 6500PLUS Auxiliary Processor Cards AIO Card 6500PLUS Asynchronous and Universal I/O CardsUIO Card Card Type Works with Port Types Split Speed Plus Universal I/O or Asynchronous I/O Card Front Panel NSO Card 6500PLUS Network Storage Option Card Plus Network Storage Option Card Token Ring Interface Module Trim Card 6500PLUS Token Ring Interface Module Option Hardware Hardware 6500PLUS Integral DSUComponents DSU InterfacePage Chapter Installation Overview Unpacking Installing Standalone UnitsSite Preparation Example Procedure InstallationStep Action Description/Result Rear View Step Action Replacing Processor Cards in Standalone Enclosures Remove the Standalone Enclosure Door Bottom of Standalone Enclosure Locking Tabs Using Screwdriver on Locking Tabs Plus Processor Card with Retaining Screw Replacement Card Step Action Installing Nodes in Modulus Enclosures AdditionalInformation Multiprocessor Multiprocessor NodesNode Example Operation Action Result/Description Replacing Master Processor of Multi-Processor Node Installing Nodes in Modulus Enclosures When To Add Another Processor with Flash Before You Begin Adding a Secondary 6500PLUS Processor with FlashStep Action Result/Description Maintaining Select Enable FlashCurrent Software Revision Select Copy Software to Flash Upgrading with Software From the New Processor Card Modulus 8/18 Installing/Replacing Processor Cards Product Description Code Requirements for Installing a Trim Card Trim Card Rear Filler Panel for Modulus 8/18 Enclosures Guidelines for Installing a Trim Card in a Modulus 8/18 Trim Card Spacing in a Modulus 18 Enclosure 10. Trim Card Rear Filler Panel for Modulus 9/21 Enclosures Installing Nodes in Modulus Enclosures 11. Trim Card In Left-most Position of Modulus 21 Enclosure Between Two Backplanes EnclosurePlus Installing Nodes in Modulus Enclosures Attaching a Trim Card Installing and Connecting a Trim Card Connecting a Trim Card Installing Cables Attaching Before Removing Removing/Replacing Trim CardsTrim Cards TRIM/Processor Card Modulus 18 with Preparing Modulus Enclosures for RFI Suppression Suppression Installing RFIScreen Modulus 18 RFI 15. RFI Suppression Straps Modulus 18 No Trim Card No Trim Card Modulus 21 RFI SuppressionBar Starting Up the Node Node StartupCtp CR Processor Card Replacing Processor Card Components Replacing DIMs New DIM Removal Jumpers 19. Jumpers on the Port Interface Pins 20. Installing Jumpers on the Port Interface Pins Guidelines Installing SIMMs 21. Simm Installation Replacing Flash Modules 22. Flash Module Installation Module Replacing ID Modules Chips Replacing Prom Chips Replacing the Cmem Chip Installing the DSU DSU DIM Installation Control Terminal Configuring the 6500PLUS for DSU Operation DSU Input and Output Signaling Input SignalsOutput Signals Loopback Options 24. Diagnostics Menu Troubleshooting Troubleshooting DSU DIM Installation DSU DIM FCC Information Type of InterfaceFacility Interface DSU DIM Installation Checking Power-Up VerificationLights Event Result/Description Diagnostics Power-Up Node Setting Node to Default Configuration Installing Software Options Access Serial Accessing Node Serial Number from Node StatisticsNumber Status/Statistics Select Node Stat 25. Serial Number on Node Stat Screen Configure Select Software Key Table Enabling a Software Access KeyFollow These Steps Install New Installing New Software Options in an Existing Network Enhanced LAN Option Cables Appendix a Function/Signal Function/Signal PinPin Name Position 35/V.36 Modulus 9/21 Enclosures Position Signal NameFunction Pin Function Signals Modulus 9/21 Enclosures 35/V.36 Signals Standalone and Modulus 8/18 Enclosures Position Name Signals Standalone and Modulus 8/18 Enclosures Pin Function Page Specifications Physical CharacteristicsUnit Dimensions Power Requirements EnvironmentalLimits DIM Index LL 2-69RS