Table of Contents | Wayne-Dalton WDSF-10, WDUSB-10R specification

Table of Contents
Table of Contents
Introduction	1
Package Contents	1
Table of Contents	2
Glossary	3
Safety Precautions	3
USB Z-Wave®Adapter Basics	4
Screen Layout Information	5
Installing ThinkEssentials®	6
Installing the USB Z-Wave®Adapter	6
ThinkEssentials® Setup	7
Z-Wave®Network Setup	7
Adding Modules to the Network	8-9
Controlling Modules	10
Drawing Floor Plan	11-12
Removing Modules from Network	13
Remove/Replace Broken Modules	14
Locking/Unlocking ThinkEssentials®	15
Creating Scenes and Zones	16-17
Modifying Scenes/Zones	18
Removing Scenes/Zones	18
Schedules Overview	19
Creating/Modifying Schedules	19-20
Viewing/Modifying Schedules	21
Deleting Schedules	21
Joining ThinkEssentials® to Existing Networks	22
Receiving Network Updates	23
Adding a Controller to the Network	24
Removing Controllers from the Network	25
Updating Secondary Controllers	26
Optimize/Repair Network	27
Polling	27
Transfer Primary Role from ThinkEssentials®	28
Transfer Primary Role to ThinkEssentials®	29
Backup Network Settings	30
Restore Network Settings	31
Command Line Option: Custom Latitude and Longitude	32
Adding Command Line Option to ThinkEssentials® Shortcut	33
Command Line Option: Multiple USB Z-Wave®Adapters	34
Command Line Option: Poll	35
Refresh Shortcut	36
Exiting ThinkEssentials®	37
Resetting ThinkEssentials®	38
Troubleshooting	39-41
Compliance	42

Table of Contents

2

Image 2

Wayne-Dalton WDSF-10, WDUSB-10R manual Table of Contents

Contents

Package Contents USB Z-Wave Adapter USB Stand Software on CD Home Control Basics Table of Contents Basics Copy See Replicate Basics Number below corresponds to the bubble number above Basics 143Screen Layout Information Installation/Setup Install USB Adapter and USB stand into computer USB port Next Use Change Location link to set your physical location Adding Modules to the Network Press ADD Device to add a Z-Wavemodule Hide Pane Button or Design tab to reveal the icon Operation Common Operations Again Drawing Floor PlanButton in the Design pane. This Erase Press Remove Device to remove a Z-Wavemodule Right-click and select Remove Broken Device Remove/Replace Broken ModulesTo remove the module from Operations Use the following procedure to lock/unlock ThinkEssentialsLocked mode the software Locking/Unlocking ThinkEssentials Scenes/Zones To include modules into this scene Modifying Scenes/Zones Remove Zone option respectively Schedules Select Scene/Zone and Action desired   Activated Pages LinkModify the desired fields per Instructions in the section Items Network Operations Joining ThinkEssentials to Existing Networks Initiate Primary Controller to Send Replication ExamplePrimary Controller Press ADD Device to add a secondary controller Adding a Controller To the networkSecondary Controller Device removed successfully message window Updating Secondary Controllers Polling Advanced OperationsOptimize/Repair Network Example Portable Controller Transfer Primary Role From ThinkessentialsInitiate Transfer in ThinkEssentials Confirmation of successful transfer Transfer Primary Role To Thinkessentials On Settings tab, select Switch to or JoinController Shift command CONTROLLER, or Controller Shift Backup Network Settings Configuration Backup file Restore commandClick the Backup or Restore Network Settings link Wayne-Dalton USB Z-Wave Section on the Settings tab Located. Note The default parent directory isCommand line window Before you begin, you must Exit Modify the Target , then click on APPLY, then OK Adding Command Line Option to ThinkEssentials ShortcutStart ThinkEssentials using the ThinkEssentials icon Type in the /multi command line option Command Line Option Multiple Z-WaveUSB AdaptersInitiate command line function ThinkEssentials /multi Initiate command line function Shortcuts Press F5 to refresh and poll the network Exiting/Closing To reset the USB Z-Wave Adapter Factory ResetResetting Thinkessentials Again On the Settings tab, click on the Reset link Troubleshooting Then select the module again It is enabled on the desired days of weekIf the modules’s icon is covered by a red Some modules do not support Switched on Set up your network againCheck to make sure that there is power Controller to my network. Now, neither Compliance US and Foreign Patents pending