Wayne-Dalton WDUSB-10R, WDSF-10 specs

Removing Modules from Network

Use the following procedure to remove Z-Wave®modules from your Z-Wave®network.

1.From the Design tab, press the REMOVE DEVICE button. A message window will ask you to press the button on the device to remove.

2.Press-and-release the PROGRAM button on the Z-Wave®module. If successful, a message window will appear stating that the device has been successfully removed. Repeat this procedure if a message window states that the module failed to be removed.

NOTE: Please see the User Manual or Instruction Manual for the specific Z-Wave®module being programmed to locate the PROGRAM button and for specific programming information.

NOTE: The process of removing modules from a network is often referred to as EXCLUSION.

NOTE: You can also reset modules in other networks using the REMOVE DEVICE button. If the target module is part of another network, it will be reset instead of removed from your network. Please note that some modules do not support being reset in this manner and so this procedure will fail; in such cases, refer to the module’s documentation for manual reset instructions.



Press REMOVE DEVICE to remove a Z-Wave®module

Press-and-Release		D		O
Press-and-Release		D		O
				N/
				O
				F
		M		F
		M
		I
		/.
PROGRAM button on			G	O
				RP

module

Device removed successfully message window.

Common Operations

13

Image 13

Wayne-Dalton WDUSB-10R, WDSF-10 manual Press Remove Device to remove a Z-Wavemodule

Contents

Home Control Basics Package Contents USB Z-Wave Adapter USB Stand Software on CD Table of Contents Copy See Replicate Basics Basics Screen Layout Information Basics 143Number below corresponds to the bubble number above Install USB Adapter and USB stand into computer USB port Installation/Setup Use Change Location link to set your physical location Next Press ADD Device to add a Z-Wavemodule Adding Modules to the Network Hide Pane Button or Design tab to reveal the icon Operation Common Operations Button in the Design pane. This Drawing Floor PlanAgain Erase Press Remove Device to remove a Z-Wavemodule To remove the module from Remove/Replace Broken ModulesRight-click and select Remove Broken Device Locked mode the software Use the following procedure to lock/unlock ThinkEssentialsOperations Locking/Unlocking ThinkEssentials Scenes/Zones To include modules into this scene Remove Zone option respectively Modifying Scenes/Zones Select Scene/Zone and Action desired Schedules Activated   Modify the desired fields per Instructions in the section LinkPages Items Joining ThinkEssentials to Existing Networks Network Operations Primary Controller ExampleInitiate Primary Controller to Send Replication Secondary Controller Adding a Controller To the networkPress ADD Device to add a secondary controller Device removed successfully message window Updating Secondary Controllers Optimize/Repair Network Advanced OperationsPolling Initiate Transfer in ThinkEssentials Transfer Primary Role From ThinkessentialsExample Portable Controller Confirmation of successful transfer Controller Shift command On Settings tab, select Switch to or JoinTransfer Primary Role To Thinkessentials CONTROLLER, or Controller Shift Configuration Backup Network Settings Click the Backup or Restore Network Settings link Restore commandBackup file Wayne-Dalton USB Z-Wave Command line window Located. Note The default parent directory isSection on the Settings tab Before you begin, you must Exit Start ThinkEssentials using the ThinkEssentials icon Adding Command Line Option to ThinkEssentials ShortcutModify the Target , then click on APPLY, then OK Initiate command line function Command Line Option Multiple Z-WaveUSB AdaptersType in the /multi command line option ThinkEssentials /multi Initiate command line function Press F5 to refresh and poll the network Shortcuts Exiting/Closing Resetting Thinkessentials Factory ResetTo reset the USB Z-Wave Adapter Again On the Settings tab, click on the Reset link Troubleshooting If the modules’s icon is covered by a red It is enabled on the desired days of weekThen select the module again Some modules do not support Check to make sure that there is power Set up your network againSwitched on Controller to my network. Now, neither US and Foreign Patents pending Compliance