284 MIDI Data Format

PARAMETER CHANGE (type operation for type 0x03:controller(LCD-Fader mode))

Reception

When [Parameter Change RX] is ON and the [Rx CH] matches the Device Channel included in the SUB STATUS, the message will be received.

When [Parameter Change ECHO] is ON, this message will be ech- oed.

When this message is received, the LCD screen, the corresponding Fader Mode, and the specified channel will be selected.

STATUS

11110000

F0

System Exclusive Message

ID No.

01000011

43

Manufacturer's ID No.(YAMAHA)

SUB STATUS

0001nnnn 1n

parameter change n=0-15(Device Chan-

 

 

 

nel No.1-16)

GROUOP ID

00111110

3e

MODEL ID

MODEL ID

00000100

04

Device code (01V)

PARAM TYPE

01000011

03

controller (type)

DATA

00000001

01

control No.(LCD-Fader mode)

 

0ddddddd dd

channel select(0-30)

 

0ddddddd dd

LCD select No.(0-17)

 

0000dddd dd

PAGE No.(0-4)

EOX

11110111

F7

End Of Exclusive

PARAMETER CHANGE (bit operation for type 0x43:controller(key remote))

Reception

When [Parameter Change RX] is ON and the [Rx CH] matches the Device Channel included in the SUB STATUS, this message will be received.

When [Parameter Change ECHO] is ON, this message will be ech- oed.

When this message is received, the same processing will be performed as when the specified key (refer to the table below) is pressed (released).

Transmission

When [Parameter Change ECHO] is ON, this message will be transmitted without change.

STATUS

11110000

F0

System Exclusive Message

 

ID No.

01000011

43

Manufacturer's ID No.(YAMAHA)

SUB STATUS

0001nnnn 1n

parameter change n=0-15(Device Chan-

 

 

 

 

nel No.1-16)

 

 

 

GROUOP ID

00111110

3e

MODEL ID

 

 

 

MODEL ID

00000100

04

Device code (01V)

 

 

PARAM TYPE

01000011

43

controller

 

 

 

DATA

00000000

00

control no.(0:key remote)

 

 

0ddddddd dd

No. 0-10,99-102(key 1-11,100-103)

 

0000dddd dd

data(bit0-2:change bit no.0-7,

 

 

 

 

 

bit3:0=reset 1=set)

 

 

 

 

:

 

:

 

 

 

EOX

11110111

F7

End Of Exclusive

 

 

KEY key no.bit0

bit1

bit2

bit3

bit4

bit5

bit6

bit7

-------------------------------------------------------------------------------------------------------------------------------------------------

key1

0

ON1

ON2

ON3

ON4

ON5

ON6

ON7

ON8

key2

1

ON9

ON10

ON11

ON12

ON13-14

ON15-16

ONSTOUT

------

key3

2

SOLO1

SOLO2

SOLO3

SOLO4

SOLO5

SOLO6

SOLO7

SOLO8

key4

3

SOLO9

SOLO10

SOLO11

SOLO12

SOLO13-14SOLO15-16

------

------

key5

4

SEL1

SEL2

SEL3

SEL4

SEL5

SEL6

SEL7

SEL8

key6

5

SEL9

SEL10

SEL11

SEL12

SEL13-14

SEL15-16

SEL STO

------

key7

6

ONRTN1

ONRTN2

SOLORT1

SOLORT2

SELRTN1

SELRTN2

HOME

MEMORY

key8

7

AUX1

AUX2

AUX3

AUX4

EFFECT1

EFFECT2

OPTION

REMOTE

key9

8

LOW

L-MID

H-MID

HIGH

------

------

------

------

key10

9

UP

LEFT

RIGHT

DOWN

ENTER

INC

DEC

------

key11

10

DYNAMIX EQ

DELAY

PAN

UTILITY

MIDI

SETUP

VIEW

key100

99

FRZ-REC

FRZ-PLAY

------

------

------

------

------

------

key101

100

SOLO1

SOLO2

SOLO3

SOLO4

SOLO5

SOLO6

SOLO7

SOLO8

key102

101

SOLO9

SOLO10

SOLO11

SOLO12

SOLO13-14SOLO15-16

SOLO-RTN1 SOLO-RTN2

key103

102

SOLO17

SOLO18

SOLO19

SOLO20

SOLO21

SOLO22

SOLO23

SOLO24

*Normally, data should be transmitted as "set(bit3=1)." In this case, the 01V will determine that that switch has been pressed and then immediately released, and will perform the appropriate processing. This means that you will not have to transmit "reset(bit3=0)" sepa- rately.

*The keys followed by 100 are virtual key, it would be the keys on LCD.

PARAMETER CHANGE (type 0x04:multiple linking)

This message is valid only for the connector that has been specified as the LINK PORT.

When two '01V' units have been connected by a cable, some of the functions (refer to the following table) will be linked.

The same LINK PORT connector settings must be made on both units.

Reception

This message is always received, and will execute the LINK function (refer to the following table). (This is not dependent on MIDI-SETUP.)

Transmission

This message is transmitted when LINK-related functions (refer to following table) are performed. (This is not dependent on MIDI-SETUP.)

When [Parameter Change ECHO] is ON, this message is transmitted without change.

STATUS

11110000

F0

System Exclusive Message

ID No.

01000011

43

Manufacturer's ID No.(YAMAHA)

SUB STATUS

0001nnnn 1n

n=0-15(Tx/Rx Channel No.1-16)

GROUOP ID

00111110

3e

MODEL ID

MODEL ID

00000100

04

Device code (01V)

PARAM TYPE

00000100

04

multiple linking

DATA

0mmfffff mf

data format (bit6-5:status, bit4-0:contents)

 

0ddddddd dd0

data #0

 

0ddddddd dd1

data #1

 

:

:

 

EOX

11110111

F7

End Of Exclusive

Status Function

 

Note

 

----------------------------------------------------------------------------------------------------------

0x00

scene recall

Recall the specified memory number

0x01

scene store

Store to the specified memory number with title

 

 

(Assign the same title to all)

0x02

scene title edit

If the title was modified, make it the same, make it

 

 

match

0x48

solo mode

Match the solo mode

 

bit6: enable/disable

 

 

bit5: on/off

 

 

bit2: recording/mixdown

 

 

bit1: sel mix/last

 

 

bit0: after fader/pre fader

 

0x60

display call

When the screen (Fader Mode) is changed, make it

 

 

match

0x61

metering point

Make the meter points match

0x62

peak hold

Make the meter Peak Hold ON/OFF match

01V—Owner’s Manual