Yamaha 376, RX-V2700, Stereo Receiver 135 En, ■Wake on RS-232Caccess, ■Remote control AMP ID, ■Remote control TUNER ID, ■User presets USER PRESET, ■Remote sensor REMOTE SENSOR

■Speaker impedance SPEAKER IMP.

Use this feature to set the speaker impedance of this unit

so that it matches that of your speakers. Choices: 8ΩMIN, 6ΩMIN

• Select “8ΩMIN” to set the speaker impedance to 8 Ω .

• Select “6ΩMIN” to set the speaker impedance to 6 Ω .

SPEAKER	Speaker	Impedance level
IMP.
		The impedance of each
	Front	speaker must be 8 Ω or
		higher.
8ΩMIN
	Center
		The impedance of each
	Surround	speaker must be 8 Ω or
		higher.
	Surround back
		The impedance of each
	Front	speaker must be 4 Ω or
		higher.
6ΩMIN
	Center
		The impedance of each
	Surround	speaker must be 6 Ω or
		higher.
	Surround back

■User presets USER PRESET

Use this feature to reset all the parameters of this unit to the initial factory settings (see page 149).

Choices: CANCEL, RESET

•Select “CANCEL” not to reset any parameters of this unit.

•Select “RESET” to reset the parameters of this unit.

Notes

•This setting completely resets all the parameters of this unit. However, the advanced setup menu parameters will not be initialized.

•The initial factory settings are activated next time you turn on this unit.

■Remote sensor REMOTE SENSOR

Use this feature to activate or deactivate the signal- receiving capability of the remote control sensor on the front panel of this unit.

Choices: ON, OFF

• Select “ON” if you want to activate the signal- receiving capability of the remote control sensor.

• Select “OFF” if you want to deactivate the signal- receiving capability of the remote control sensor.

Note

We recommend setting the parameter to “ON” in most cases.

ADVANCED SETUP

■Wake on RS-232C access

WAKE ON RS232C

Use this feature to set this unit to transmit data via the RS- 232C interface when this unit is in the standby mode. Choices: YES, NO

Initial setting:

[U.S.A. and Canada models]: YES

[Other models]: NO

•Select “YES” to set this unit to transmit data via the RS-232C interface.

•Select “NO” to set this unit not to transmit data via the RS-232C interface.

■Remote control AMP ID

RC AMP ID

Use this feature to set the AMP ID of this unit for remote control recognition (see page 121).

Choices: ID1, ID2

•Select “ID1” when the remote control AMP ID library code is set to “2001”.

•Select “ID2” when the remote control AMP ID library code is set to “2002”.

Note

You need to set the corresponding remote control AMP library code for the remote control (see page 121).

■Remote control TUNER ID

RC TUNER ID

Use this feature to set the TUNER ID of this unit for remote control recognition (see page 138).

Choices: ID1, ID2

•Select “ID1” when the remote control TUNER ID library code is set to “2602”.

•Select “ID2” when the remote control TUNER ID library code is set to “2603”.

Note

You need to set the corresponding remote control TUNER library code for the remote control (see page 138).

■Remote control XM ID RC XM ID

(U.S.A. and Canada models only)

Use this feature to set the XM ID of this unit for remote control recognition (see page 138).

Choices: ID1, ID2

•Select “ID1” when the remote control XM ID library code is set to “2604”.

•Select “ID2” when the remote control XM ID library code is set to “2605”.

Note

You need to set the corresponding remote control XM library code for the remote control (see page 138).

OPERATION ADVANCED

135 En