TROUBLESHOOTING
During Auto Setup
Error message | Cause | Remedy | See | |
page | ||||
|
|
| ||
E01:No Front SP | Front L/R channel signals are not detected. | Check the front L/R speaker connections. | ||
|
|
|
| |
E02:No Sur. SP | A surround channel signal is not detected. | Check the surround speaker connections. | ||
|
|
|
| |
E03:No PRNS SP | A presence channel signal is not detected. | Check the presence speaker connections. | ||
|
|
|
| |
Only right surround back channel signal is | Connect the surround back speaker to the |
| ||
| detected. | LEFT SURROUND BACK SPEAKERS | ||
|
| terminal if you only have one surround | ||
|
|
| ||
|
| back speaker. |
| |
|
|
|
| |
E05:Noisy | Background noise is too loud. | Try running “Auto Setup” in a quiet | — | |
|
| environment. | ||
|
|
| ||
|
|
|
| |
|
| Turn off noisy electric equipment like air |
| |
|
| conditioners or move them away from the | — | |
|
| optimizer microphone. |
| |
|
|
|
| |
E06:Check Sur. | Surround back speakers are connected, | Connect surround speakers when you use | ||
| though surround L/R speakers are not. | surround back speakers. | ||
|
| |||
|
|
|
| |
E07:No MIC | The optimizer microphone was unplugged | Connect the supplied optimizer microphone |
| |
| during the “Auto Setup” procedure. | to the OPTIMIZER MIC jack on the front | ||
|
| panel. |
| |
|
|
|
| |
E08:No Signal | The optimizer microphone does not detect | Check the microphone setting. | ||
| test tones. |
|
| |
| Check the speaker connections and | |||
|
| |||
|
| placement. | ||
|
|
| ||
|
|
|
| |
E09:User Cancel | The “Auto Setup” procedure was cancelled | Run “Auto Setup” again. | ||
| due to user activity. |
| ||
|
|
| ||
|
|
|
| |
E10:Internal Err. | An internal error occurred. | Run “Auto Setup” again. | ||
|
|
|
| |
After Auto Setup |
|
|
|
Warning message | Cause | Remedy | See | |
page | ||||
|
|
| ||
W1:Out of Phase | Speaker polarity is not correct. This | Check the speaker connections for proper |
| |
| message may appear depending on the | polarity (+ or | ||
| speakers even when the speakers are |
| ||
|
|
| ||
| connected correctly. |
|
| |
|
|
|
| |
W2:Over Distance | The distance between the speaker and the | Bring the speaker closer to the listening | — | |
| listening position is over 24 m (80 ft). | position. | ||
|
| |||
|
|
|
| |
W3:Level Error | The difference of volume level among | Readjust the speaker installation so that all |
| |
| speakers is excessive. | speakers are set in locations with similar | — | |
|
| conditions. |
| |
|
|
|
| |
|
| Check the speaker connections. | ||
|
|
|
| |
|
| Use speakers of similar quality. | — | |
|
|
|
| |
|
| Adjust the output volume of the subwoofer. | ||
|
|
|
| |
W4:SP Mismatch | The result of the wiring check of “Auto | Use “Speaker Set” in “Manual Setup” to |
| |
| Setup” is different from “Speaker Set” in | adjust the speaker settings manually. | ||
| “Manual Setup”. |
|
| |
|
|
|
|
Notes
•If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “Auto Setup” again.
•If warning “W1” appears, corrections are made, but they may not be optimal.
•If warning “W2” or “W3” appears, no corrections are made.
•If error “E10” occurs repeatedly, please contact a qualified YAMAHA service center.