![](/images/backgrounds/19931/19931-174144x1.png)
TROUBLESHOOTING
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
No picture. | The output and input for the picture are | Set “Conversion” to “On” or connect your source | ||
| connected to different types of video | components in the same way as you connect your |
| |
| jacks. | video monitor to this unit. |
| |
|
|
|
| |
|
|
| ||
|
|
|
| |
Short message | “Short Message” is set to “OFF”. | Set “Short Message” to “On”. | ||
displays do not |
|
|
| |
“Wall Paper” is set to “None”. | Set “Wall Paper” to “Yes” or “Gray”. | |||
appear in the video | ||||
monitor. |
|
|
| |
“Conversion” is set to “Off”. | Set “Conversion” to “On”. | |||
| ||||
|
|
|
| |
| The signals input at the HDMI IN1, |
|
| |
| HDMI IN2 or HDMI IN3 jack are being |
|
| |
| output at the HDMI OUT jack. |
|
| |
|
|
|
| |
| Video signals in the progressive format or |
|
| |
| HDTV video signals are being input. |
|
| |
|
|
|
| |
The sound suddenly | The protection circuitry has been activated | Check that the speaker impedance setting is correct. | ||
goes off. | because of a short circuit, etc. |
|
| |
Check that the speaker wires are not touching each | — | |||
|
| |||
|
| other and then turn this unit back on. |
| |
|
|
|
| |
| The sleep timer has turned off this unit. | Turn on this unit, and play the source again. | — | |
|
|
|
| |
| The sound is muted. | Press MUTE or VOLUME +/– on the remote control | ||
|
| to resume audio output. |
| |
|
|
|
| |
Sound is heard from | Incorrect cable connections. | Connect the cables properly. If the problem persists, | ||
the speaker on one |
| the cables may be defective. |
| |
side only. |
|
|
| |
Incorrect settings in “Speaker Level”. | Adjust the “Speaker Level” settings. | |||
| ||||
|
|
|
| |
Only the center | When playing a monaural source with a |
|
| |
speaker outputs | CINEMA DSP program, the source signal |
|
| |
substantial sound. | is directed to the center channel, and the |
|
| |
| front and surround speakers output effect |
|
| |
| sounds. |
|
| |
|
|
|
| |
No sound is heard | “Center” in “Speaker Set” is set to | Set “Center” to “Small” or “Large”. | ||
from the center | “None”. |
|
| |
speaker. |
|
|
| |
One of the HiFi DSP programs (except for | Try another sound field program. | |||
| ||||
| “7ch Stereo”) has been selected. |
|
| |
|
|
|
| |
No sound is heard | The sound field programs are turned off. | Press STRAIGHT to turn them on. | ||
from the presence |
|
|
| |
You are using a source or program | Try another sound field program. | |||
speakers. | ||||
| combination that does not output sound |
|
| |
| from all channels. |
|
| |
|
|
|
| |
No sound is heard | “Surround” in “Speaker Set” is set to | Set “Surround” to “Small” or “Large”. | ||
from the surround | “None”. |
|
| |
speakers. |
|
|
| |
This unit is in the “STRAIGHT” mode | Press STRAIGHT on the front panel so that | |||
| ||||
| and a monaural source is being played | “STRAIGHT” disappears from the front panel |
| |
| back. | display. |
| |
|
|
|
| |
No sound is heard | “Bass Out” in “Speaker Set” is set to | Set “Bass Out” to “SWFR” or “Both”. | ||
from the subwoofer. | “Front” when a Dolby Digital or DTS |
|
| |
| signal is being played. |
|
| |
|
|
|
| |
| “Bass Out” in “Speaker Set” is set to | Set “Bass Out” to “Both”. | ||
| “SWFR” or “Front” when a |
|
| |
| source is being played. |
|
| |
|
|
|
|
The source does not contain low- frequency signals.