Clean the Printhead, 101 | Zebra Technologies TTP 8000 instruction

Maintenance

Clean the Printhead

Clean the Printhead

The printhead can be cleaned without removal.

1.Caution • Disconnect the printer from the power source before performing the following procedure.

Remove the power from the printer.

2.Caution • While performing any tasks near an open printhead, remove all rings, watches, hanging necklaces, identification badges, or other metallic objects that could touch the printhead.

Open the printhead by pulling the two release levers back and tilt up the printhead.

3.Caution • The printhead may be hot and could cause severe burns. Allow the printhead to cool.

Clean the heat elements with a cotton swab immersed in ethyl or isopropyl alcohol.

Note • Zebra recommends using a clean swab dipped in a solution of isopropyl alcohol (minimum 90%) and deionized water (maximum 10%) to clean the print head.

101

10/19/2009

TTP 8000 Technical Manual

P1003638-003

Image 101

Zebra Technologies TTP 8000 manual Clean the Printhead, 101

Contents

Zebra TTP P1003638-003 TTP 8000 Technical Manual 10/19/2009 Contents Setup Default Parameter SettingsOperation Programming Specifications 105 MaintenanceInterface 11 中国 RoHS 材料声明 China RoHS Material Declaration Index Contents Updating IntroductionAbout This Manual Mail address emb@zebra.com Subject line Emaillist Contacts TTP 8000 Printers Product Presentation Printer Exterior, Side View Printer Exterior, Rear View Indicators Weekend low Control Board IndicatorsPaper low Feed Button Using the Feed buttonIs there paper in the presenter section of the printer? Black mark Unpacking Installation Looping presenter version Compact version Installation Considerations Ambient Light Electrostatic Discharges, and Earth Currents Using the Parallel Interface Connecting to the Computer You can see the hardware revision on the self-test printout Using the USB Interface All black printing 10 a 12 a Connecting the PowerNone Idle 15 a Paper Width Paper Path AdjustmentMaking a Test Printout Sensors on Large Roll Holder Paper Level Sensors Paper-near-end Sensor Connection Installing a Printer Driver Installation Operation Tear off approximately 0.5 m from the new paper roll Installing a Paper RollPreparations Using Manual Load Using Auto Load Loosen both thumbscrews and flip open the presenter top Clearing Paper Jams Power on Modes Self-test Printout and Other Power on ModesNormal Released Dont care Self-test printout Operation Programming Printout Styles Is the popular command name that should be easy to remember How the commands are describedGive the command in hex representation Give the command in decimal representation Summary Of Control Codes & Escape Sequences 4A n1 Paper Advance 27 105 n1 Italics6A n1 Paper Reverse N1...n2 Send dot-line, 300 dpi Black Mark Top-Of-Form Commands Software Command Syntax Changes the alignment of text and logotypes Text CommandsLeft Center ESC ! n1 Select Font Turns OFF Italics Normal Turns on Italics Gives reversed print, white on black Selects normal or reversed printGives normal print, black on white Data Ignore LF See CR/LF Behavior on This command is used to increase the line spacing Ends the string Graphics commands Enables compression Disables compression ESCl000 or ESCs00 ESCr000011930243 ESC g n Print Logotype Form feed Clear presenter Print commandsRun presenter Print buffer full Press on Feed Button ESC J n1 Paper Advance You can also use RS together with the paper advance command Cut and Present CommandsTo auto, see parameter 49 on Gives a cut & eject after the last text line Retracts the presented Ejects the presented Erases all logotypes stored in the flash Prom System Related Commands Erases all fonts stored in the flash Prom Set several parameters at once ESC NUL Status reporting commands Paper-near-end Enquiry Fonts and Logotype Enquiry Escenqe to fetch it Read← 0 0 02 2B C6 28 hex, or 0 0 2 43 198 40 dec Read← n Where n can be ‘A’ Ascii or 41 hex or 65 dec Send→ ESCENQ11 ESC ENQ E Wait for Parameters in the temporary setup Loading Fonts File Format Character Bitmap Data Header Logotypes Printing All logotypes are erased with the ESC&L command Status Reporting Programming Default Parameter Settings Burn Time How the Parameters are Described Summary of Parameter Settings Serial Interface Set-up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not Controls what the printer does with buffered data Print SetupPrint text at once but spool graphic data Print graphic data but spool text Pixels or font height, whichever is the largest Disable the loopCm loop LF = Ignored CR = Ignored Varies with the contents printouts Black mark mode is selected n36=2Form length No cut 102 mm Statement 92 mmLetter Legal Sets max black mark length to 15 mm Fixed Document ModeSets min black mark length to 4 mm Feeds 50 mm between black mark and cut Basket disabled Eject uncollected page when new page is printed. WasteEject uncollected page when new page is printed. Page not Retracts uncollected page when new page is printed Sets Letter width Sets A4 width Feed 2 mm Automatic Distance CalculationFeed 255 mm Automatic Distance Calculation means advancing the paper Locked Setup Printable Area N41, n42 N39 Recommended Black Mark Size and Position Aligning Preprint and Thermal Print Parameter n34 Auto Cut Parameters Used Garbage, Black Mark and Out Of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Simple Calibration Process Black-mark Sensing from Within Windows Setup Interface + Ö Parallel Error Signaling Data + Data Ground Cable ground Cable power Maintenance 100 Fault Finding 101 Clean the Printhead 102 FirmwareFirmware and Hardware Revisions 103 104 Specifications General Information Serial Interface SettingsPrint Data 106 107 Paper Handling 108 Text Modes Non-Windows Applications 109 Character Sets 110 111 112 113 Printer Dimensions Measurements Drawing, Compact Printer 114 115 116 100W Power Supply 117 118 Measurements Drawing, Printer 01744-xxx with Roll Holder for 119 120 Environmental ConditionsMiscellaneous General Paper SpecificationThermal Coating Perforation 122 Be moved if you adjust the sensor positionPreprinting 123 Black Mark Size and Position Part Number List AccessoriesPrinters 124 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006 标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration 126 Index Index Index Index Page Zebra Technologies Europe Limited