Text Commands, Left, Center, Right | Zebra Technologies TTP 8000

Programming

Text Commands

Text Commands

Text received by the printer is printed with the currently selected font and font attributes. Text exceeding the page width is wrapped with the line spacing selected.

37

ESC o n1

1B 6F n1	hex
27 111 n1	decimal

Text and Logotype Orientation

Changes the orientation of text and logotypes.

n = 0

n = 1

Gives portrait orientation

Gives landscape orientation

Portrait and landscape can be mixed on the same printout. There are two cursors, one for portrait and one for landscape. The cursor always starts at the top left corner of the document. Looking at the paper when it exits the printer, the portrait cursor is at the top left corner of the printout, moving to the right as text is typed, while the landscape cursor is at the top right corner, moving downwards.

			Note • Landscape orientation can only be used with fixed document mode.

ESC N n1			Align Text
1B	4E n1	hex	Align Text
27	78 n1	decimal

Changes the alignment of text and logotypes.

ESC N 0=	Left
ESC N 1=	Center
ESC N 2=	Right

10/19/2009

TTP 8000 Technical Manual

P1003638-003

Image 37

Zebra Technologies TTP 8000 manual Text Commands, Changes the alignment of text and logotypes, Left, Center, Right

Contents

Zebra TTP P1003638-003 TTP 8000 Technical Manual 10/19/2009 Contents Setup Default Parameter SettingsOperation Programming Specifications 105 MaintenanceInterface 11 中国 RoHS 材料声明 China RoHS Material Declaration Index Contents About This Manual IntroductionUpdating Mail address emb@zebra.com Subject line Emaillist Contacts TTP 8000 Printers Product Presentation Printer Exterior, Side View Printer Exterior, Rear View Indicators Paper low Control Board IndicatorsWeekend low Feed Button Using the Feed buttonIs there paper in the presenter section of the printer? Black mark Unpacking Installation Looping presenter version Compact version Installation Considerations Ambient Light Electrostatic Discharges, and Earth Currents Using the Parallel Interface Connecting to the Computer You can see the hardware revision on the self-test printout Using the USB Interface None Idle 15 a Connecting the PowerAll black printing 10 a 12 a Making a Test Printout Paper Path AdjustmentPaper Width Sensors on Large Roll Holder Paper Level Sensors Paper-near-end Sensor Connection Installing a Printer Driver Installation Operation Preparations Installing a Paper RollTear off approximately 0.5 m from the new paper roll Using Manual Load Using Auto Load Loosen both thumbscrews and flip open the presenter top Clearing Paper Jams Power on Modes Self-test Printout and Other Power on ModesNormal Released Dont care Self-test printout Operation Programming Printout Styles Is the popular command name that should be easy to remember How the commands are describedGive the command in hex representation Give the command in decimal representation Summary Of Control Codes & Escape Sequences 4A n1 Paper Advance 27 105 n1 Italics6A n1 Paper Reverse N1...n2 Send dot-line, 300 dpi Black Mark Top-Of-Form Commands Software Command Syntax Changes the alignment of text and logotypes Text CommandsLeft Center ESC ! n1 Select Font Turns OFF Italics Normal Turns on Italics Gives normal print, black on white Selects normal or reversed printGives reversed print, white on black Data Ignore LF See CR/LF Behavior on This command is used to increase the line spacing Ends the string Graphics commands Enables compression Disables compression ESCl000 or ESCs00 ESCr000011930243 ESC g n Print Logotype Form feed Clear presenter Print commandsRun presenter Print buffer full Press on Feed Button ESC J n1 Paper Advance You can also use RS together with the paper advance command Cut and Present CommandsTo auto, see parameter 49 on Gives a cut & eject after the last text line Retracts the presented Ejects the presented Erases all logotypes stored in the flash Prom System Related Commands Erases all fonts stored in the flash Prom Set several parameters at once ESC NUL Status reporting commands Paper-near-end Enquiry Fonts and Logotype Enquiry Escenqe to fetch it Read← 0 0 02 2B C6 28 hex, or 0 0 2 43 198 40 dec Read← n Where n can be ‘A’ Ascii or 41 hex or 65 dec Send→ ESCENQ11 ESC ENQ E Wait for Parameters in the temporary setup Loading Fonts File Format Character Bitmap Data Header Logotypes Printing All logotypes are erased with the ESC&L command Status Reporting Programming Default Parameter Settings Burn Time How the Parameters are Described Summary of Parameter Settings Serial Interface Set-up No flow control Select what handshaking to use on the serial interfaceXon / Xoff No, paper out and error signals are not Parallel Port SetupYes, paper out and error signals are disabled Controls what the printer does with buffered data Print SetupPrint text at once but spool graphic data Print graphic data but spool text Cm loop Disable the loopPixels or font height, whichever is the largest LF = Ignored CR = Ignored Varies with the contents printouts Black mark mode is selected n36=2Form length No cut 102 mm Statement 92 mmLetter Legal Sets max black mark length to 15 mm Fixed Document ModeSets min black mark length to 4 mm Feeds 50 mm between black mark and cut Basket disabled Eject uncollected page when new page is printed. WasteEject uncollected page when new page is printed. Page not Retracts uncollected page when new page is printed Sets Letter width Sets A4 width Feed 2 mm Automatic Distance CalculationFeed 255 mm Automatic Distance Calculation means advancing the paper Locked Setup Printable Area N41, n42 N39 Recommended Black Mark Size and Position Aligning Preprint and Thermal Print Parameter n34 Auto Cut Parameters Used Garbage, Black Mark and Out Of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Simple Calibration Process Black-mark Sensing from Within Windows Setup Interface + Ö Parallel Error Signaling Data + Data Ground Cable ground Cable power Maintenance 100 Fault Finding 101 Clean the Printhead Firmware and Hardware Revisions Firmware102 103 104 Specifications General Information Serial Interface SettingsPrint Data 106 107 Paper Handling 108 Text Modes Non-Windows Applications 109 Character Sets 110 111 112 113 Printer Dimensions Measurements Drawing, Compact Printer 114 115 116 100W Power Supply 117 118 Measurements Drawing, Printer 01744-xxx with Roll Holder for 119 Miscellaneous Environmental Conditions120 General Paper SpecificationThermal Coating Perforation Preprinting Be moved if you adjust the sensor position122 123 Black Mark Size and Position Part Number List AccessoriesPrinters 124 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006 标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration 126 Index Index Index Index Page Zebra Technologies Europe Limited