Feed Button, Using the Feed button | Zebra Technologies TTP 8000

14

Product Presentation

Feed Button

Feed Button

When you have inserted the paper under the printhead, press the Feed button and the printer will feed it forward, cut and eject a printout, then switch to on-line mode. Each press on the Feed button will feed, cut, and present one form length.

Using the Feed button:

Is there paper in the presenter section of the printer?

If…	Then…

No	Press the Feed button once to make a Form Feed. (Feed, cut, and present a
	complete page.) In black mark mode, the page will be synchronized with the
	black mark.

Yes	Press the Feed button once to clear the presenter.

When auto-loading paper, and the paper does not feed straight:

1.Press the Feed button once to stop the loading process.

2.Correct the error.

3.Press the Feed button once more to commence with the loading.

When loading paper manually:

1.After closing the printhead, press the Feed button to feed-cut-eject one page.

2.Press and hold the Feed button while turning on the power to print a self-test printout. See page Making a Test Printout on page 21.

P1003638-003

TTP 8000 Technical Manual

10/19/2009

Image 14

Zebra Technologies TTP 8000 Feed Button, Using the Feed button, Is there paper in the presenter section of the printer?

Contents

Zebra TTP P1003638-003 TTP 8000 Technical Manual 10/19/2009 Contents Operation Default Parameter SettingsSetup Programming Interface MaintenanceSpecifications 105 11 中国 RoHS 材料声明 China RoHS Material Declaration Index Contents Updating IntroductionAbout This Manual Contacts Mail address emb@zebra.com Subject line Emaillist Product Presentation TTP 8000 Printers Printer Exterior, Side View Printer Exterior, Rear View Indicators Weekend low Control Board IndicatorsPaper low Is there paper in the presenter section of the printer? Using the Feed buttonFeed Button Black mark Installation Unpacking Installation Considerations Looping presenter version Compact version Electrostatic Discharges, and Earth Currents Ambient Light Connecting to the Computer Using the Parallel Interface Using the USB Interface You can see the hardware revision on the self-test printout All black printing 10 a 12 a Connecting the PowerNone Idle 15 a Paper Width Paper Path AdjustmentMaking a Test Printout Paper Level Sensors Sensors on Large Roll Holder Installing a Printer Driver Paper-near-end Sensor Connection Installation Operation Tear off approximately 0.5 m from the new paper roll Installing a Paper RollPreparations Using Auto Load Using Manual Load Clearing Paper Jams Loosen both thumbscrews and flip open the presenter top Normal Released Dont care Self-test Printout and Other Power on ModesPower on Modes Self-test printout Operation Programming Printout Styles Give the command in hex representation How the commands are describedIs the popular command name that should be easy to remember Give the command in decimal representation Summary Of Control Codes & Escape Sequences 6A n1 Paper Reverse 27 105 n1 Italics4A n1 Paper Advance N1...n2 Send dot-line, 300 dpi Software Command Syntax Black Mark Top-Of-Form Commands Left Text CommandsChanges the alignment of text and logotypes Center Turns OFF Italics Normal Turns on Italics ESC ! n1 Select Font Gives reversed print, white on black Selects normal or reversed printGives normal print, black on white Data See CR/LF Behavior on Ignore LF This command is used to increase the line spacing Graphics commands Ends the string Disables compression Enables compression ESCl000 or ESCs00 ESCr000011930243 ESC g n Print Logotype Run presenter Print commandsForm feed Clear presenter Print buffer full Press on Feed Button ESC J n1 Paper Advance To auto, see parameter 49 on Cut and Present CommandsYou can also use RS together with the paper advance command Gives a cut & eject after the last text line Ejects the presented Retracts the presented System Related Commands Erases all logotypes stored in the flash Prom Erases all fonts stored in the flash Prom Set several parameters at once ESC NUL Status reporting commands Paper-near-end Enquiry Fonts and Logotype Enquiry Escenqe to fetch it Read← n Where n can be ‘A’ Ascii or 41 hex or 65 dec Read← 0 0 02 2B C6 28 hex, or 0 0 2 43 198 40 dec Send→ ESCENQ11 ESC ENQ E Parameters in the temporary setup Wait for Fonts Loading File Format Character Bitmap Data Logotypes Header All logotypes are erased with the ESC&L command Printing Status Reporting Programming Default Parameter Settings How the Parameters are Described Burn Time Summary of Parameter Settings Serial Interface Set-up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not Print text at once but spool graphic data Print SetupControls what the printer does with buffered data Print graphic data but spool text Pixels or font height, whichever is the largest Disable the loopCm loop CR = Ignored LF = Ignored Form length Black mark mode is selected n36=2Varies with the contents printouts No cut Letter 92 mm102 mm Statement Legal Sets min black mark length to 4 mm Fixed Document ModeSets max black mark length to 15 mm Feeds 50 mm between black mark and cut Eject uncollected page when new page is printed. Page not Eject uncollected page when new page is printed. WasteBasket disabled Retracts uncollected page when new page is printed Sets A4 width Sets Letter width Feed 255 mm Automatic Distance Automatic Distance CalculationFeed 2 mm Calculation means advancing the paper Locked Setup N41, n42 N39 Printable Area Aligning Preprint and Thermal Print Recommended Black Mark Size and Position Parameters Used Parameter n34 Auto Cut Garbage, Black Mark and Out Of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Black-mark Sensing from Within Windows Simple Calibration Process Setup Interface Parallel + Ö Error Signaling Cable power Data + Data Ground Cable ground Maintenance Fault Finding 100 Clean the Printhead 101 102 FirmwareFirmware and Hardware Revisions 103 104 Specifications Print Data Serial Interface SettingsGeneral Information 106 Paper Handling 107 Text Modes Non-Windows Applications 108 Character Sets 109 110 111 112 Printer Dimensions 113 114 Measurements Drawing, Compact Printer 115 100W Power Supply 116 117 118 119 Measurements Drawing, Printer 01744-xxx with Roll Holder for 120 Environmental ConditionsMiscellaneous Thermal Coating Paper SpecificationGeneral Perforation 122 Be moved if you adjust the sensor positionPreprinting Black Mark Size and Position 123 Printers AccessoriesPart Number List 124 中国 RoHS 材料声明 China RoHS Material Declaration 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006 标准规定的限量要求。 126 Index Index Index Index Page Zebra Technologies Europe Limited