Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies TTP 8000 manual Esc Enq E

Models: TTP 8000

1 132

Download 132 pages 5.96 Kb

Page 62

62

Programming

System Related Commands

ESC ENQ E		Read Extended Status
1B 05 45	hex	Read Extended Status
27 5 69	decimal

Extended status is status from the printer together with devices connected to the I2C options- bus available in some Zebra printers. The short message protocol gives replies up to 255 bytes. Other protocols may be defined in the future. Protocols are described in separate documents.

<ESC><ENQ>E results in a variable length reply:

n1	Protocol version, 11h = Short Message Protocol

n2	Protocol length in bytes

n3-n255	Data specified by the protocol

Short message status examples:

Suppose we have a printer with a shutter attached.

Example 1 – Out of paper, presenter Jam and Shutter Open Jam.

Hex

01	Status code 1 (shutter device)

C1	Device Shutter

07	Satus code 7 (printer device)

03	Status code 3 (printer device)

80	Device local host (printer)

05	Tag message length (bytes)

01	Tag ID: Status messages

07	Protocol Length in bytes

11	Protocol SM, version 1 (short message)

Example 2 – No errors in any device.

Hex

00	Tag message length (bytes)

01	Protocol SM, version 1 (short message)

02	Protocol Length in bytes

11	Tag ID: Status messages

P1003638-003

TTP 8000 Technical Manual

10/19/2009

Image 62

Zebra Technologies TTP 8000 manual Esc Enq E

Contents

Zebra TTP P1003638-003 TTP 8000 Technical Manual 10/19/2009 Contents Operation Default Parameter SettingsSetup ProgrammingInterface MaintenanceSpecifications 105 11 中国 RoHS 材料声明 China RoHS Material Declaration IndexContents Updating IntroductionAbout This Manual Contacts Mail address emb@zebra.com Subject line EmaillistProduct Presentation TTP 8000 PrintersPrinter Exterior, Side View Printer Exterior, Rear View Indicators Weekend low Control Board IndicatorsPaper low Is there paper in the presenter section of the printer? Using the Feed buttonFeed Button Black markInstallation UnpackingInstallation Considerations Looping presenter version Compact versionElectrostatic Discharges, and Earth Currents Ambient LightConnecting to the Computer Using the Parallel InterfaceUsing the USB Interface You can see the hardware revision on the self-test printoutAll black printing 10 a 12 a Connecting the PowerNone Idle 15 a Paper Width Paper Path AdjustmentMaking a Test Printout Paper Level Sensors Sensors on Large Roll HolderInstalling a Printer Driver Paper-near-end Sensor ConnectionInstallation Operation Tear off approximately 0.5 m from the new paper roll Installing a Paper RollPreparations Using Auto Load Using Manual LoadClearing Paper Jams Loosen both thumbscrews and flip open the presenter topNormal Released Dont care Self-test Printout and Other Power on ModesPower on Modes Self-test printoutOperation Programming Printout Styles Give the command in hex representation How the commands are describedIs the popular command name that should be easy to remember Give the command in decimal representationSummary Of Control Codes & Escape Sequences 6A n1 Paper Reverse 27 105 n1 Italics4A n1 Paper Advance N1...n2 Send dot-line, 300 dpiSoftware Command Syntax Black Mark Top-Of-Form CommandsLeft Text CommandsChanges the alignment of text and logotypes CenterTurns OFF Italics Normal Turns on Italics ESC ! n1 Select FontGives reversed print, white on black Selects normal or reversed printGives normal print, black on white Data See CR/LF Behavior on Ignore LFThis command is used to increase the line spacing Graphics commands Ends the stringDisables compression Enables compressionESCl000 or ESCs00 ESCr000011930243 ESC g n Print Logotype Run presenter Print commandsForm feed Clear presenter Print buffer full Press on Feed ButtonESC J n1 Paper Advance To auto, see parameter 49 on Cut and Present CommandsYou can also use RS together with the paper advance command Gives a cut & eject after the last text lineEjects the presented Retracts the presentedSystem Related Commands Erases all logotypes stored in the flash PromErases all fonts stored in the flash Prom Set several parameters at once ESC NUL Status reporting commands Paper-near-end Enquiry Fonts and Logotype Enquiry Escenqe to fetch it Read← n Where n can be ‘A’ Ascii or 41 hex or 65 dec Read← 0 0 02 2B C6 28 hex, or 0 0 2 43 198 40 decSend→ ESCENQ11 ESC ENQ E Parameters in the temporary setup Wait forFonts LoadingFile Format Character Bitmap Data Logotypes HeaderAll logotypes are erased with the ESC&L command PrintingStatus Reporting Programming Default Parameter Settings How the Parameters are Described Burn TimeSummary of Parameter Settings Serial Interface Set-up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not Print text at once but spool graphic data Print SetupControls what the printer does with buffered data Print graphic data but spool textPixels or font height, whichever is the largest Disable the loopCm loop CR = Ignored LF = IgnoredForm length Black mark mode is selected n36=2Varies with the contents printouts No cutLetter 92 mm102 mm Statement LegalSets min black mark length to 4 mm Fixed Document ModeSets max black mark length to 15 mm Feeds 50 mm between black mark and cutEject uncollected page when new page is printed. Page not Eject uncollected page when new page is printed. WasteBasket disabled Retracts uncollected page when new page is printedSets A4 width Sets Letter widthFeed 255 mm Automatic Distance Automatic Distance CalculationFeed 2 mm Calculation means advancing the paperLocked Setup N41, n42 N39 Printable AreaAligning Preprint and Thermal Print Recommended Black Mark Size and PositionParameters Used Parameter n34 Auto CutGarbage, Black Mark and Out Of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Black-mark Sensing from Within Windows Simple Calibration ProcessSetup Interface Parallel + ÖError Signaling Cable power Data + Data Ground Cable groundMaintenance Fault Finding 100Clean the Printhead 101102 FirmwareFirmware and Hardware Revisions 103 104 Specifications Print Data Serial Interface SettingsGeneral Information 106Paper Handling 107Text Modes Non-Windows Applications 108Character Sets 109110 111 112 Printer Dimensions 113114 Measurements Drawing, Compact Printer115 100W Power Supply 116117 118 119 Measurements Drawing, Printer 01744-xxx with Roll Holder for120 Environmental ConditionsMiscellaneous Thermal Coating Paper SpecificationGeneral Perforation122 Be moved if you adjust the sensor positionPreprinting Black Mark Size and Position 123Printers AccessoriesPart Number List 124中国 RoHS 材料声明 China RoHS Material Declaration 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006 标准规定的限量要求。126 Index Index Index Index Page Zebra Technologies Europe Limited