Printing | Zebra Technologies TTP 8000 specs

68

Programming

Logotypes

Printing

To print a logotype, send <ESC>g<n1><n2><n3><n4><n5> where n1 is the logotype number, n2n3 is the horizontal print position, and n4n5 is the vertical print position of the upper left corner of the logotype.

n1	One byte logotype number, (0—15)

n2n3	Two byte X position measured in pixels from the left-hand edge of the
	print window.

n4n5	These bytes (Y-position) must be inserted, but they are ignored as a
	logotype is always printed at the current Y-position.

Erasing

All logotypes are erased with the <ESC>&L command.

Caution • Loading to the flash PROM will erase the RAM completely since the RAM is used during the loading process. Any print data residing in RAM will thus be lost.

P1003638-003

TTP 8000 Technical Manual

10/19/2009

Image 68

Zebra Technologies TTP 8000 manual Printing, All logotypes are erased with the ESC&L command

Contents

Zebra TTP P1003638-003 TTP 8000 Technical Manual 10/19/2009 Contents Default Parameter Settings SetupOperation Programming Maintenance Specifications 105Interface 11 中国 RoHS 材料声明 China RoHS Material Declaration Index Contents Updating IntroductionAbout This Manual Contacts Mail address emb@zebra.com Subject line Emaillist Product Presentation TTP 8000 Printers Printer Exterior, Side View Printer Exterior, Rear View Indicators Weekend low Control Board IndicatorsPaper low Using the Feed button Feed ButtonIs there paper in the presenter section of the printer? Black mark Installation Unpacking Installation Considerations Looping presenter version Compact version Electrostatic Discharges, and Earth Currents Ambient Light Connecting to the Computer Using the Parallel Interface Using the USB Interface You can see the hardware revision on the self-test printout All black printing 10 a 12 a Connecting the PowerNone Idle 15 a Paper Width Paper Path AdjustmentMaking a Test Printout Paper Level Sensors Sensors on Large Roll Holder Installing a Printer Driver Paper-near-end Sensor Connection Installation Operation Tear off approximately 0.5 m from the new paper roll Installing a Paper RollPreparations Using Auto Load Using Manual Load Clearing Paper Jams Loosen both thumbscrews and flip open the presenter top Self-test Printout and Other Power on Modes Power on ModesNormal Released Dont care Self-test printout Operation Programming Printout Styles How the commands are described Is the popular command name that should be easy to rememberGive the command in hex representation Give the command in decimal representation Summary Of Control Codes & Escape Sequences 27 105 n1 Italics 4A n1 Paper Advance6A n1 Paper Reverse N1...n2 Send dot-line, 300 dpi Software Command Syntax Black Mark Top-Of-Form Commands Text Commands Changes the alignment of text and logotypesLeft Center Turns OFF Italics Normal Turns on Italics ESC ! n1 Select Font Gives reversed print, white on black Selects normal or reversed printGives normal print, black on white Data See CR/LF Behavior on Ignore LF This command is used to increase the line spacing Graphics commands Ends the string Disables compression Enables compression ESCl000 or ESCs00 ESCr000011930243 ESC g n Print Logotype Print commands Form feed Clear presenterRun presenter Print buffer full Press on Feed Button ESC J n1 Paper Advance Cut and Present Commands You can also use RS together with the paper advance commandTo auto, see parameter 49 on Gives a cut & eject after the last text line Ejects the presented Retracts the presented System Related Commands Erases all logotypes stored in the flash Prom Erases all fonts stored in the flash Prom Set several parameters at once ESC NUL Status reporting commands Paper-near-end Enquiry Fonts and Logotype Enquiry Escenqe to fetch it Read← n Where n can be ‘A’ Ascii or 41 hex or 65 dec Read← 0 0 02 2B C6 28 hex, or 0 0 2 43 198 40 dec Send→ ESCENQ11 ESC ENQ E Parameters in the temporary setup Wait for Fonts Loading File Format Character Bitmap Data Logotypes Header All logotypes are erased with the ESC&L command Printing Status Reporting Programming Default Parameter Settings How the Parameters are Described Burn Time Summary of Parameter Settings Serial Interface Set-up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not Print Setup Controls what the printer does with buffered dataPrint text at once but spool graphic data Print graphic data but spool text Pixels or font height, whichever is the largest Disable the loopCm loop CR = Ignored LF = Ignored Black mark mode is selected n36=2 Varies with the contents printoutsForm length No cut 92 mm 102 mm StatementLetter Legal Fixed Document Mode Sets max black mark length to 15 mmSets min black mark length to 4 mm Feeds 50 mm between black mark and cut Eject uncollected page when new page is printed. Waste Basket disabledEject uncollected page when new page is printed. Page not Retracts uncollected page when new page is printed Sets A4 width Sets Letter width Automatic Distance Calculation Feed 2 mmFeed 255 mm Automatic Distance Calculation means advancing the paper Locked Setup N41, n42 N39 Printable Area Aligning Preprint and Thermal Print Recommended Black Mark Size and Position Parameters Used Parameter n34 Auto Cut Garbage, Black Mark and Out Of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Black-mark Sensing from Within Windows Simple Calibration Process Setup Interface Parallel + Ö Error Signaling Cable power Data + Data Ground Cable ground Maintenance Fault Finding 100 Clean the Printhead 101 102 FirmwareFirmware and Hardware Revisions 103 104 Specifications Serial Interface Settings General InformationPrint Data 106 Paper Handling 107 Text Modes Non-Windows Applications 108 Character Sets 109 110 111 112 Printer Dimensions 113 114 Measurements Drawing, Compact Printer 115 100W Power Supply 116 117 118 119 Measurements Drawing, Printer 01744-xxx with Roll Holder for 120 Environmental ConditionsMiscellaneous Paper Specification GeneralThermal Coating Perforation 122 Be moved if you adjust the sensor positionPreprinting Black Mark Size and Position 123 Accessories Part Number ListPrinters 124 中国 RoHS 材料声明 China RoHS Material Declaration 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006 标准规定的限量要求。 126 Index Index Index Index Page Zebra Technologies Europe Limited