Interface | Zebra Technologies TTP 8000 manual

8

Interface

The printer has two interfaces as standard, parallel and USB. There are no selections to be made, but normally only one interface should be used at a time. The printer may not function properly if data is received on more than one interface at a time.

Caution • Always use Zebra-approved interface cables. Using a non-approved cable with the printer may void the FCC and other EMC approvals of the printer.

Caution • If you connect both parallel and USB cables, the voltage that the host computer outputs on the parallel port may be enough to give signals out on the USB-interface even if the power of the printer is turned OFF!

These signals can result in the operating system of the host computer detecting the printer as on and available when it's not.

Another effect of these false signals is that after turning the printer on and off to clear an error condition, the printer is dead to Windows.

Always disconnect the parallel interface cable when using USB!

10/19/2009

TTP 8000 Technical Manual

P1003638-003

Image 95

Zebra Technologies TTP 8000 manual Interface

Contents

Zebra TTP P1003638-003 TTP 8000 Technical Manual 10/19/2009 Contents Programming Default Parameter SettingsSetup Operation 11 中国 RoHS 材料声明 China RoHS Material Declaration Index MaintenanceSpecifications 105 Interface Contents Updating IntroductionAbout This Manual Mail address emb@zebra.com Subject line Emaillist Contacts TTP 8000 Printers Product Presentation Printer Exterior, Side View Printer Exterior, Rear View Indicators Weekend low Control Board IndicatorsPaper low Black mark Using the Feed buttonFeed Button Is there paper in the presenter section of the printer? Unpacking Installation Looping presenter version Compact version Installation Considerations Ambient Light Electrostatic Discharges, and Earth Currents Using the Parallel Interface Connecting to the Computer You can see the hardware revision on the self-test printout Using the USB Interface All black printing 10 a 12 a Connecting the PowerNone Idle 15 a Paper Width Paper Path AdjustmentMaking a Test Printout Sensors on Large Roll Holder Paper Level Sensors Paper-near-end Sensor Connection Installing a Printer Driver Installation Operation Tear off approximately 0.5 m from the new paper roll Installing a Paper RollPreparations Using Manual Load Using Auto Load Loosen both thumbscrews and flip open the presenter top Clearing Paper Jams Self-test printout Self-test Printout and Other Power on ModesPower on Modes Normal Released Dont care Operation Programming Printout Styles Give the command in decimal representation How the commands are describedIs the popular command name that should be easy to remember Give the command in hex representation Summary Of Control Codes & Escape Sequences N1...n2 Send dot-line, 300 dpi 27 105 n1 Italics4A n1 Paper Advance 6A n1 Paper Reverse Black Mark Top-Of-Form Commands Software Command Syntax Center Text CommandsChanges the alignment of text and logotypes Left ESC ! n1 Select Font Turns OFF Italics Normal Turns on Italics Gives reversed print, white on black Selects normal or reversed printGives normal print, black on white Data Ignore LF See CR/LF Behavior on This command is used to increase the line spacing Ends the string Graphics commands Enables compression Disables compression ESCl000 or ESCs00 ESCr000011930243 ESC g n Print Logotype Print buffer full Press on Feed Button Print commandsForm feed Clear presenter Run presenter ESC J n1 Paper Advance Gives a cut & eject after the last text line Cut and Present CommandsYou can also use RS together with the paper advance command To auto, see parameter 49 on Retracts the presented Ejects the presented Erases all logotypes stored in the flash Prom System Related Commands Erases all fonts stored in the flash Prom Set several parameters at once ESC NUL Status reporting commands Paper-near-end Enquiry Fonts and Logotype Enquiry Escenqe to fetch it Read← 0 0 02 2B C6 28 hex, or 0 0 2 43 198 40 dec Read← n Where n can be ‘A’ Ascii or 41 hex or 65 dec Send→ ESCENQ11 ESC ENQ E Wait for Parameters in the temporary setup Loading Fonts File Format Character Bitmap Data Header Logotypes Printing All logotypes are erased with the ESC&L command Status Reporting Programming Default Parameter Settings Burn Time How the Parameters are Described Summary of Parameter Settings Serial Interface Set-up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not Print graphic data but spool text Print SetupControls what the printer does with buffered data Print text at once but spool graphic data Pixels or font height, whichever is the largest Disable the loopCm loop LF = Ignored CR = Ignored No cut Black mark mode is selected n36=2Varies with the contents printouts Form length Legal 92 mm102 mm Statement Letter Feeds 50 mm between black mark and cut Fixed Document ModeSets max black mark length to 15 mm Sets min black mark length to 4 mm Retracts uncollected page when new page is printed Eject uncollected page when new page is printed. WasteBasket disabled Eject uncollected page when new page is printed. Page not Sets Letter width Sets A4 width Calculation means advancing the paper Automatic Distance CalculationFeed 2 mm Feed 255 mm Automatic Distance Locked Setup Printable Area N41, n42 N39 Recommended Black Mark Size and Position Aligning Preprint and Thermal Print Parameter n34 Auto Cut Parameters Used Garbage, Black Mark and Out Of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Simple Calibration Process Black-mark Sensing from Within Windows Setup Interface + Ö Parallel Error Signaling Data + Data Ground Cable ground Cable power Maintenance 100 Fault Finding 101 Clean the Printhead 102 FirmwareFirmware and Hardware Revisions 103 104 Specifications 106 Serial Interface SettingsGeneral Information Print Data 107 Paper Handling 108 Text Modes Non-Windows Applications 109 Character Sets 110 111 112 113 Printer Dimensions Measurements Drawing, Compact Printer 114 115 116 100W Power Supply 117 118 Measurements Drawing, Printer 01744-xxx with Roll Holder for 119 120 Environmental ConditionsMiscellaneous Perforation Paper SpecificationGeneral Thermal Coating 122 Be moved if you adjust the sensor positionPreprinting 123 Black Mark Size and Position 124 AccessoriesPart Number List Printers 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006 标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration 126 Index Index Index Index Page Zebra Technologies Europe Limited