Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies TTP 8000 manual Self-test Printout and Other Power on Modes, Self-test printout

Models: TTP 8000

1 132

Download 132 pages 5.96 Kb

Page 29

Operation

Self-test Printout and Other Power ON Modes

Self-test Printout and Other Power ON Modes

1.Remove power from the printer.

If your printer has a power switch, turn the power off. If it does not, remove power to the printer.

2.Hold the feed-forward button depressed while powering ON the printer. Keep the button depressed until the presenter motor buzzes.

This produces a printout showing the firmware program version and date, control board revision number and serial number, name of loaded fonts and logotypes, parameter settings, and the set printhead burn-time.

3.Each successive press of the button will produce a test printout.

4.To exit self-test mode, switch the printer OFF and ON, or send a reset command.

Note • You can also print a self-test printout by sending the command <ESC>P<0> to the printer.

29

Power ON Modes

Normally the printer is immediately ready for use when you switch it ON. You can enable several test and maintenance functions by giving simulating sensor signals while switching ON the power.

Print Mode	Feed button	Paper	Printhead

Normal	Released	Don't care	Don’t care

Self-test printout	Pressed	Loaded	Down

Important • For printers without head up sensor, modes requiring printhead-up are not supported.

10/19/2009

TTP 8000 Technical Manual

P1003638-003

Image 29

Zebra Technologies TTP 8000 Self-test Printout and Other Power on Modes, Normal Released Dont care, Self-test printout

Contents

Zebra TTP P1003638-003 TTP 8000 Technical Manual 10/19/2009 Contents Setup Default Parameter SettingsOperation ProgrammingSpecifications 105 MaintenanceInterface 11 中国 RoHS 材料声明 China RoHS Material Declaration IndexContents Updating IntroductionAbout This Manual Mail address emb@zebra.com Subject line Emaillist ContactsTTP 8000 Printers Product PresentationPrinter Exterior, Side View Printer Exterior, Rear View Indicators Weekend low Control Board IndicatorsPaper low Feed Button Using the Feed buttonIs there paper in the presenter section of the printer? Black markUnpacking InstallationLooping presenter version Compact version Installation ConsiderationsAmbient Light Electrostatic Discharges, and Earth CurrentsUsing the Parallel Interface Connecting to the ComputerYou can see the hardware revision on the self-test printout Using the USB InterfaceAll black printing 10 a 12 a Connecting the PowerNone Idle 15 a Paper Width Paper Path AdjustmentMaking a Test Printout Sensors on Large Roll Holder Paper Level SensorsPaper-near-end Sensor Connection Installing a Printer DriverInstallation Operation Tear off approximately 0.5 m from the new paper roll Installing a Paper RollPreparations Using Manual Load Using Auto LoadLoosen both thumbscrews and flip open the presenter top Clearing Paper JamsPower on Modes Self-test Printout and Other Power on ModesNormal Released Dont care Self-test printoutOperation Programming Printout Styles Is the popular command name that should be easy to remember How the commands are describedGive the command in hex representation Give the command in decimal representationSummary Of Control Codes & Escape Sequences 4A n1 Paper Advance 27 105 n1 Italics6A n1 Paper Reverse N1...n2 Send dot-line, 300 dpiBlack Mark Top-Of-Form Commands Software Command SyntaxChanges the alignment of text and logotypes Text CommandsLeft CenterESC ! n1 Select Font Turns OFF Italics Normal Turns on ItalicsGives reversed print, white on black Selects normal or reversed printGives normal print, black on white Data Ignore LF See CR/LF Behavior onThis command is used to increase the line spacing Ends the string Graphics commandsEnables compression Disables compressionESCl000 or ESCs00 ESCr000011930243 ESC g n Print Logotype Form feed Clear presenter Print commandsRun presenter Print buffer full Press on Feed ButtonESC J n1 Paper Advance You can also use RS together with the paper advance command Cut and Present CommandsTo auto, see parameter 49 on Gives a cut & eject after the last text lineRetracts the presented Ejects the presentedErases all logotypes stored in the flash Prom System Related CommandsErases all fonts stored in the flash Prom Set several parameters at once ESC NUL Status reporting commands Paper-near-end Enquiry Fonts and Logotype Enquiry Escenqe to fetch it Read← 0 0 02 2B C6 28 hex, or 0 0 2 43 198 40 dec Read← n Where n can be ‘A’ Ascii or 41 hex or 65 decSend→ ESCENQ11 ESC ENQ E Wait for Parameters in the temporary setupLoading FontsFile Format Character Bitmap Data Header LogotypesPrinting All logotypes are erased with the ESC&L commandStatus Reporting Programming Default Parameter Settings Burn Time How the Parameters are DescribedSummary of Parameter Settings Serial Interface Set-up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not Controls what the printer does with buffered data Print SetupPrint text at once but spool graphic data Print graphic data but spool textPixels or font height, whichever is the largest Disable the loopCm loop LF = Ignored CR = IgnoredVaries with the contents printouts Black mark mode is selected n36=2Form length No cut102 mm Statement 92 mmLetter LegalSets max black mark length to 15 mm Fixed Document ModeSets min black mark length to 4 mm Feeds 50 mm between black mark and cutBasket disabled Eject uncollected page when new page is printed. WasteEject uncollected page when new page is printed. Page not Retracts uncollected page when new page is printedSets Letter width Sets A4 widthFeed 2 mm Automatic Distance CalculationFeed 255 mm Automatic Distance Calculation means advancing the paperLocked Setup Printable Area N41, n42 N39Recommended Black Mark Size and Position Aligning Preprint and Thermal PrintParameter n34 Auto Cut Parameters UsedGarbage, Black Mark and Out Of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Simple Calibration Process Black-mark Sensing from Within WindowsSetup Interface + Ö ParallelError Signaling Data + Data Ground Cable ground Cable powerMaintenance 100 Fault Finding101 Clean the Printhead102 FirmwareFirmware and Hardware Revisions 103 104 Specifications General Information Serial Interface SettingsPrint Data 106107 Paper Handling108 Text Modes Non-Windows Applications109 Character Sets110 111 112 113 Printer DimensionsMeasurements Drawing, Compact Printer 114115 116 100W Power Supply117 118 Measurements Drawing, Printer 01744-xxx with Roll Holder for 119120 Environmental ConditionsMiscellaneous General Paper SpecificationThermal Coating Perforation122 Be moved if you adjust the sensor positionPreprinting 123 Black Mark Size and PositionPart Number List AccessoriesPrinters 124表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006 标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration126 Index Index Index Index Page Zebra Technologies Europe Limited