Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies TTP 8000 manual Default Parameter Settings

Models: TTP 8000

1 132

Download 132 pages 5.96 Kb

Page 71

6

Default Parameter Settings

Some of the printer settings can be stored in the flash PROM so that they will be used also after power OFF.

The stored parameter settings are printed out on the self-test printout (see Self-test Printout and Other Power ON Modes on page 29).

The number in front of the function is the parameter number (n) used when setting the parameter with the command <ESC>&P<n><v>.

You can use the parameter settings pretty much like normal commands. Either send the parameter values with each printout, or set them up once and then send <ESC>&<4> to store all settings in the flash PROM.

You can always return to factory default settings by sending <ESC>&<F><10>, and then storing those settings with <ESC>&<4>.

Note • The parameters can be locked so that no changes are possible. Check parameter 53 on the self-test printout to find out.

Note • If you try to set a parameter to an invalid value, the parameter will be set to the nearest valid value below.

10/19/2009

TTP 8000 Technical Manual

P1003638-003

Image 71

Zebra Technologies TTP 8000 manual Default Parameter Settings

Contents

Zebra TTP P1003638-003 TTP 8000 Technical Manual 10/19/2009 Contents Programming Default Parameter SettingsSetup Operation11 中国 RoHS 材料声明 China RoHS Material Declaration Index MaintenanceSpecifications 105 InterfaceContents Updating IntroductionAbout This Manual Mail address emb@zebra.com Subject line Emaillist ContactsTTP 8000 Printers Product PresentationPrinter Exterior, Side View Printer Exterior, Rear View Indicators Weekend low Control Board IndicatorsPaper low Black mark Using the Feed buttonFeed Button Is there paper in the presenter section of the printer?Unpacking InstallationLooping presenter version Compact version Installation ConsiderationsAmbient Light Electrostatic Discharges, and Earth CurrentsUsing the Parallel Interface Connecting to the ComputerYou can see the hardware revision on the self-test printout Using the USB InterfaceAll black printing 10 a 12 a Connecting the PowerNone Idle 15 a Paper Width Paper Path AdjustmentMaking a Test Printout Sensors on Large Roll Holder Paper Level SensorsPaper-near-end Sensor Connection Installing a Printer DriverInstallation Operation Tear off approximately 0.5 m from the new paper roll Installing a Paper RollPreparations Using Manual Load Using Auto LoadLoosen both thumbscrews and flip open the presenter top Clearing Paper JamsSelf-test printout Self-test Printout and Other Power on ModesPower on Modes Normal Released Dont careOperation Programming Printout Styles Give the command in decimal representation How the commands are describedIs the popular command name that should be easy to remember Give the command in hex representationSummary Of Control Codes & Escape Sequences N1...n2 Send dot-line, 300 dpi 27 105 n1 Italics4A n1 Paper Advance 6A n1 Paper ReverseBlack Mark Top-Of-Form Commands Software Command SyntaxCenter Text CommandsChanges the alignment of text and logotypes LeftESC ! n1 Select Font Turns OFF Italics Normal Turns on ItalicsGives reversed print, white on black Selects normal or reversed printGives normal print, black on white Data Ignore LF See CR/LF Behavior onThis command is used to increase the line spacing Ends the string Graphics commandsEnables compression Disables compressionESCl000 or ESCs00 ESCr000011930243 ESC g n Print Logotype Print buffer full Press on Feed Button Print commandsForm feed Clear presenter Run presenterESC J n1 Paper Advance Gives a cut & eject after the last text line Cut and Present CommandsYou can also use RS together with the paper advance command To auto, see parameter 49 onRetracts the presented Ejects the presentedErases all logotypes stored in the flash Prom System Related CommandsErases all fonts stored in the flash Prom Set several parameters at once ESC NUL Status reporting commands Paper-near-end Enquiry Fonts and Logotype Enquiry Escenqe to fetch it Read← 0 0 02 2B C6 28 hex, or 0 0 2 43 198 40 dec Read← n Where n can be ‘A’ Ascii or 41 hex or 65 decSend→ ESCENQ11 ESC ENQ E Wait for Parameters in the temporary setupLoading FontsFile Format Character Bitmap Data Header LogotypesPrinting All logotypes are erased with the ESC&L commandStatus Reporting Programming Default Parameter Settings Burn Time How the Parameters are DescribedSummary of Parameter Settings Serial Interface Set-up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not Print graphic data but spool text Print SetupControls what the printer does with buffered data Print text at once but spool graphic dataPixels or font height, whichever is the largest Disable the loopCm loop LF = Ignored CR = IgnoredNo cut Black mark mode is selected n36=2Varies with the contents printouts Form lengthLegal 92 mm102 mm Statement LetterFeeds 50 mm between black mark and cut Fixed Document ModeSets max black mark length to 15 mm Sets min black mark length to 4 mmRetracts uncollected page when new page is printed Eject uncollected page when new page is printed. WasteBasket disabled Eject uncollected page when new page is printed. Page notSets Letter width Sets A4 widthCalculation means advancing the paper Automatic Distance CalculationFeed 2 mm Feed 255 mm Automatic DistanceLocked Setup Printable Area N41, n42 N39Recommended Black Mark Size and Position Aligning Preprint and Thermal PrintParameter n34 Auto Cut Parameters UsedGarbage, Black Mark and Out Of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Simple Calibration Process Black-mark Sensing from Within WindowsSetup Interface + Ö ParallelError Signaling Data + Data Ground Cable ground Cable powerMaintenance 100 Fault Finding101 Clean the Printhead102 FirmwareFirmware and Hardware Revisions 103 104 Specifications 106 Serial Interface SettingsGeneral Information Print Data107 Paper Handling108 Text Modes Non-Windows Applications109 Character Sets110 111 112 113 Printer DimensionsMeasurements Drawing, Compact Printer 114115 116 100W Power Supply117 118 Measurements Drawing, Printer 01744-xxx with Roll Holder for 119120 Environmental ConditionsMiscellaneous Perforation Paper SpecificationGeneral Thermal Coating122 Be moved if you adjust the sensor positionPreprinting 123 Black Mark Size and Position124 AccessoriesPart Number List Printers表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006 标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration126 Index Index Index Index Page Zebra Technologies Europe Limited