Baldor GLC30, GLC60, GLC105, GLC45, GLC20, GLC65, GLC100, GLC15, GLC25, GLC40 manual Symbols, Operation

Page 6

Symbols

This symbol is shown throughout the manual to indicate a connection to ground reference point.

Indicates a potentially hazardous situation which, if not avoided, could result in injury or death.

Indicates a potentially hazardous situation which, if not avoided, could result in injury or death.

Precaution Statements Used In This Manual

There are three classifications of precautionary statements used in this manual. The most critical is a WARNING statement, then the Caution statement and the least critical is the Note statement. The usage of each statement is as follows:

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in injury or death.

Caution: Indicates a potentially hazardous situation which, if not avoided, could result in damage to property.

Note:

Additional information that is not critical to the installation or operation.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS - This manual contains important instructions for the generator that should be followed during installation, operation and maintenance of the generator and battery (batteries). For ease of reading, the Warning statements are divided into four categories: Operation, Burn, Installation, and Maintenance.

Operation

WARNING: Never operate this generator in a manner other than as described in this manual. Operation in any manner not described in this manual should be considered unsafe and should not be attempted. Never start the engine unless you have first verified that the installation and operation of the generator are as described in this manual.

WARNING: Be sure that you are completely familiar with the safe operation of this equipment. This equipment may be connected to other machines that have rotating parts or parts that are controlled by this equipment. Improper use can cause serious or fatal injury.

WARNING: Exhaust fumes/gases are extremely dangerous and can cause severe illness or death. Never breath exhaust fumes produced by a running engine. Only run the engine outdoors where ventilation is plentiful. Exhaust gases contain carbon monoxide, a colorless, odorless and extremely dangerous gas that can cause unconsciousness or death. Symptoms of carbon monoxide poisoning include: dizziness, nausea, headaches, sleepiness, vomiting or incoherence. If you or anyone else experiences these symptoms, get out into fresh air immediately. Stop the engine and do not restart the engine until it has been inspected and if necessary repaired or reinstalled in a well ventilated area.

WARNING: Hot exhaust gasses must never be directed toward anything that may catch fire or explode.

WARNING: This generator must not be used on or near any forest covered, brush covered, or grass covered land unless the engine's exhaust system is equipped with a spark arrestor. The spark arrestor must be maintained in effective working order by the operator.

WARNING: Some parts of this generator rotate during operation. Rotating parts can present extreme danger if clothing or body extremities are caught by the rotating part and can cause serious or fatal injury. Never touch a part of the generator until the engine has been stopped and all rotating parts are completely stopped. Also, disconnect the spark plug wires and battery connection to prevent accidental engine rotation during servicing.

WARNING: Never move a generator set that is running. Loads should be connected and position secure before starting the engine. Hazards are caused by moving a generator set that is running.

Continued on next page.

1‐2 Product Safety Information

MN2408

Image 6
Contents GLC Generator MN2408California Proposition 65 Warning Table of Contents Troubleshooting and Maintenance Problems and Solutions Appendix aAppendix B Section Product Safety Information Read This Manual ThoroughlySymbols OperationOperation Warning Statements Burn Installation Battery Safety Maintenance Any warranty coverage Limited WarrantyWarranty Period Generator Series Labor Parts‐2 General Information MN2408 Installation Guidelines Site PlanningExhaust System Controls and Transfer SwitchEngine Cooling System Room AirFoundation Design Foundation Checklist Setting The Genset On An Existing Concrete Floor SlabVibration Isolators Weight Of The Genset ‐2 Approximate Weight vs. kW OutputDesigning An Isolated Foundation ‐3 Calculate Soil Bearing Load SBL Capacity‐5 Typical Foundation Installation Soil Type Safe Bearing Capacity Lb per ft Kilo PascalsExhaust System ‐6 Exhaust System Calculations Exhaust Piping Transfer Switch Transfer Switch ChecklistTransfer Switch Location Battery Starting System Battery LocationBattery Charger Battery Cables‐14 General Information MN2408 When the Generator is installed outdoors ‐1 Generator LiftingGenerator Open ‐2 Mounting Dimensions‐3 Stub Up Detail SoundSecure the Generator Ventilation TestHot Exhaust Gasses Backpressure must not exceed 20 of water columnGuidelines for Exhaust System Page Fuel Connections ‐4 Fuel Consumption Natural and LPVGeneral Considerations Natural Gas Connections External Supply Piping by installerExample Determining Pipe Size for Natural Gas Pipe Iron Pipe Size LengthExample Determining Pipe Size for LPV ‐6 LP Vapor Flow Rate Cubic Feet per Hour per Pipe LengthCatalog No Rating Transfer Switch Considerations Single Phase Power ConnectionsRemote Start AC Power Connections Ground Neutral L1L2 ConnectionsConnections Battery Charger Considerations General Wiring ConsiderationsGLC100 Recommended Engine Oil and Battery TypeGLC10-25 GLC125Post Installation Checks Post Installation Checks ‐16 Receiving & Installation MN2408 ‐8 Alarm & Warning Conditions Digital Engine Controller Description EM0046A21 MRS17AUT Mode OFF ModeMAN Mode Digital Engine Controller Description EM0046A21 MRS17ECU Alarm List Adjustment MenuAlarm List Menu Status Condition of Transition Action  Next StateShut down SD see ‐10 AlarmsSensor fail FLS see ‐10 ‐10 Possible Warnings‐12 Binary outputs Inputs and Outputs‐11 Binary Inputs Used for shunt tripSet points ‐13 Analog Inputs‐14 Basic Setpoints ‐15 Engine Setpoints ‐16 Engine Protect Setpoints Delay for Analog Input 2 Wrn Wtemp low. s Range1-180 s‐15 Engine Setpoints During the first 500ms. ,1s Range 0 3s‐17 Generator Protect Setpoints ‐18 Sensor Spec Setpoints ‐19 IOM/PTM Module Setpoints‐11 Controller Connection Diagram Jdic Run Switch Alarm LEDSpeed Signal LED OFF SwitchOperator Control Panel Manual Start/StopAutomatic Start/Stop Automatic Fault Shutdown Automatic Mains Failure AMFUtility Normal Condition Utility Power Failure ConditionsUtility Power Restored Load Test Push-button OperationFault Digital Inputs Name Action Terminal # Internal FaultsDigital Input Faults No Load Test‐15 Engine Controller Inputs & Outputs Analog Faults Fault Inputs Name Action SignalEngine starter motor Such as Fuel Rack Solenoids or electronic governorsCrank Fail Programmable ContactsAction Description Display Comments Show Operating Status screens Apply Power Main LCD DisplayReset faults Name and remaining timeGenerator Phase Current Display Generator Phase Voltage Display Line to LineGenerator Phase/Neutral Voltage Display Line to Neutral Generator Average Output DisplayProgram Menus Navigation Hints Main Menu Loop Voltage Calibration Procedure Zero CalibrationRepeat for each phase Span CalibrationDisplayed values Engine Temperature & Oil Pressure Calibration Displays the type of calibration functionOil Pressure ‐16 Configuration Data Sheet 120-15000V AC Parameter Setting RangeSystem Voltage Line To Line Toggle Between Psi/KpaParameter Setting ‐21 Engine Control Connections ‐34 Operation MN2408 General EngineProblems and Solutions ‐1 General Troubleshooting GuideProblem Possible Cause Remedy ‐2 Troubleshooting Guide Digital Controller Only ‐3 Troubleshooting Guide Analog Controller Only ServiceVerify the adjustments. Replace controller if failed Battery Battery ChargerInstallation Considerations Options & Accessories A‐1Figure A‐2 Battery Heating Pad Installation BTHTR81 Heater Options & Accessories A‐3 Engine Block HeaterSilencers GLC10-25 GLC30-45 GLC60-90 GLC100-105Options & Accessories A‐5 Fuel Strainers & Fuel LinesFuel Strainer Figure A‐6 Installation StopOptions & Accessories A‐7 Remote AnnuciatorsGLC30-60 Radiator Duct FlangeGenerator GLC80-100GLC10-25 H1=36.0 L1=11.75 GLC30-45 H1=52.1, H2=66.6 Options & Accessories A‐9Enclosures GLC60-90 H1=64.2, H2=76.8‐10 Series GLC MN2408 OSH Plant Qty per PhaseGLC Circuit Breaker & Electrical Data Series GLC B‐1Figure B‐11 Customer Interface Connection Diagram Series GLC B‐3 Figure B‐13 Single Phase w/o Breaker Connection Diagram Figure B‐14 Single Phase One Breaker Connection Diagram Series GLC B‐5Figure B‐15 Single Phase Two Breaker Connection Diagram Series GLC B‐7 ‐8 Series GLC MN2408 Series GLC B‐9 ‐10 Series GLC MN2408 Figure B‐20 Three Phase Connection Diagram Series GLC B‐11Figure B‐21 Three Phase Connection Diagram with PMG Series GLC B‐13 ‐14 Series GLC MN2408 Series GLC B‐15 ‐16 Series GLC MN2408 Series GLC B‐17 Figure B‐27 Control Box Connections with MEC20 Controller Series GLC B‐19 Figure B‐29 Control Box Connections with MEC2 Controller Figure B‐30 Engine Wiring, Woodward 4.3L GM Series GLC B‐21Figure B‐31 Engine Wiring, Woodward 5.7L GM Figure B‐32 Engine Wiring, Woodward 8.1L GM Series GLC B‐23‐24 Series GLC MN2408 Baldor District Offices Baldor Electric Company MN2408