Intel 31154 manual Pull-Up/Pull-Down Terminations Sheet 6, Serial Eeprom

Terminations
Table 5.	Pull-Up/Pull-Down Terminations (Sheet 6 of 9)
Signal		Pull-Up/Pull-Down or Termination (See Note 1)	Comments
		To enable Opaque Memory Base/Limit Registers
		to establish a private memory space for secondary
		bus usage:
OPAQUE_EN		• Pull high to 3.3 V through an external 8.2 KΩ
		resistor.
		To disable Opaque Memory Base/Limit Registers:
		• Pull low to GND through an external 220 Ω
		resistor (default).
		To enable device hiding after reset (in other words,
		to hide device numbers 16–21 from the host):
		• Pull high to 3.3 V through an external resistor.
IDSEL_MASK		To disable device hiding after reset:
		• Pull low to GND through an external 220 Ω
		resistor (default).
		After reset, device hiding can be performed
		through software through the Secondary IDSEL
		Select Register (Offset 5Ch).
		This bit is used by the system management
		software to help the user identify the best slot for
		an add-in card:
		• When the 31154 is installed on an add-in card
		and the add-in card implements a 64-bit PCI
DEV_64BIT#		connector, pull up to 3.3 V through an external
		8.2 KΩ resistor.
		• When the 31154 is not installed on an add-in
		card or the add-in card implements only a
		32-bit PCI connector, pull low to GND through
		a 220 Ω external resistor (default).
Serial EEPROM
		Serial ROM clock input:
SR_CLK		• Connect to the clock input of the EEPROM.
		• NC when EEPROM is not required in design.
		Serial ROM data input:
SR_DI		• Connect to the DI input of the EEPROM.
		• NC when EEPROM is not required in design.
		Serial ROM data output:	NOTE: When EEPROM is present but register
SR_DO		• Connect to the DO output of the EEPROM.	preload is not desired, bits[7:6] of the first
			byte can be any value except the preload
		• Tie high or pull to GND when EEPROM is not
			enable value (10b).
		required in design.
		Serial ROM chip select:
SR_CS		• Connect to the chip select of the EEPROM.
		• NC when EEPROM is not required in design.

NOTES:

1.The recommended value for pull-up resistors for PCI applications is 5.6 KΩ (note that the minimum value for PCI 3.3 V signaling RMIN = 2.42 KΩ, RTYP = 8.2 KΩ, as per the PCI Local Bus Specification, Revision 2.3, section 4.3.3).

2.The recommended value for pull-up resistors for PCI-X applications is 8.2 KΩ. For PCI-X, the minimum pull-up resistor value is 5 KΩ, as per the PCI-X Addendum to the PCI Local Bus Specification, Revision 1.0b, section 9.7.

3.For plug-in card implementations, the pull-up must be on the motherboard.

4.Connect PVIO and SVIO pull-up resistors to 5 V or 3.3 V power supply through an external resistor—25 Ω (5 V) or

0 Ω (3.3 V), depending on the signaling level of the primary/secondary PCI bus. Refer to the power-sequencing guidelines in Section 8.2 on page 58.

24 Intel® 31154 133 MHz PCI Bridge Design Guide Design Guide