ENGLISH
INSTALLATION INSTRUCTIONS (continued)
Installation and Cabling
Connecting to a PC
■ Read SAFETY GUIDELINES ( I to VII ) carefully to ensure maximum safety before proceeding to these steps:
1)Make sure that the display signals produced by your PC meet the specifications of this product.
•For the specifications of this product, see Product Specifications ( 27 to 29 ).
2)Choose an appropriate site and install the product on a level table where the stand is secure.
•Install the monitor to have ready access to a power socket available.
3)Make sure that your PC’s power switch is off.
4)Interconnect the signal input terminal (RGB1) on the monitor rear panel and the display signal output terminal of the PC to each other using the signal cable included.
•Optional cables are needed to connect to the RGB2 input and audio input terminals.
•If the signal cable included does not match your PC, consult your dealer after reading the section “Signal Input”. 28
5)Insert one end of the power cable included into the
6)Turn on the monitor, then the PC to make sure that a display image appears on the monitor screen.
•For instructions on turning on the monitor and adjusting its display images, see “Operating Instructions” ( 9 to 19 ).
Speaker (R) |
|
|
|
|
|
|
|
|
| Monitor rear panel | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Speaker (L) | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Power cable connector
AUDIO IN
Power | RGB 1 |
cable |
|
V H B G R
To signal input terminals
To signal
output terminal
To signal input terminals
To signal
output terminal
To audio input terminals
3.5mm Stereo mini jack
To audio output terminal
Cord Clamper
When connecting a computer audio input to the unit (using a 3.5mm stereo mini jack), the cord must pass through the cord clamp toward the bottom of the back of
PC
the main unit. If it does not, there is a possibility of insufficient suppression of electromagnetic radiation.
6