Bay Technical Associates DS Series, DS62-MD4 Detail Operations and Configurations, Main Screen

Page 14

DS62-Network, DS62-MD4 Network/Modem Host Module

Detail Operations and Configurations

NOTE: Depending on the DS-Series model, the menus may vary according to the number of DS74 modules installed in the unit. If this is not an initial set-up and Password has already been enabled, you are prompted to login. After logging in successfully, invoke the main menu by sending the attention character five times (;;;;;).

NOTE: Password feature is case sensitive. Default is ‘root/baytech’.

Main Screen

DS62-MD4

IMPORTANT: The Factory default serial communications parameters are 9600 bps, 8 data bits, 1 stop bit, and no parity.

With a proper connection to the unit upon power-up or unit reset, the following initialization and Status menu will be displayed except the number of outlets will be dependent on the specific DS unit:

DS-Series - F 2.10.05

(C) 2005 Bay

Technical Associates

Module Name: DS62-MD4

 

 

Module: 1

 

 

 

Attention Character: ;

1

 

Device A

(2 ,1)

 

Device B

(2 ,2)

2

 

Device C

(2 ,3)

3

 

Device D

(2 ,4)

4

 

DS-RPC

(5 ,1)

5

Current configuration

Status

S

Configure

C

Make Changes

Unit Reset

RU

Resets the DS-Unit, terminates internal &

 

 

 

external modem connections, allow 10

Logout

T

seconds for reset.

Enter Request :c

 

 

 

 

 

 

 

NOTE: Only the Administrator user will see the configuration option.

IMPORTANT: If you get the following message after selecting the ‘Configure’ option, the other port has the configuration option selected.

Configuration mode in use.

IMPORTANT: Once you make a change to any of the Configuration options, you have to back out of the Configuration menu and will be asked to ‘Accept’ changes. If you type ‘Y’ for YES and press <cr>, the changes take effect immediately for the serial port. For the Ethernet port you must do a Unit Reset to get the changes to take effect.

14

Image 14
Contents DS Series Manual DS62-Network, DS62-MD4 Network/Modem Host Module EIA-232 Serial Connection DS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module Internal Modem Connection InstallationConnection Description Power Quick Start Host ModuleSerial Setup DS-DS Login Setup Menu Access ControlNetwork Port Configuration Radius ConfigurationSignal RS-232 COM Port Port DS Port RPC DE-9 Pin DB-25 Pin DS62 EIA-232 RJ-45 Signal Pin DirectionAdapters Signals Description CablingAdapters Detail Operations and Configurations Main ScreenUnit Configuration Menu Configuration StatusDTR RTS Handshaking Serial Port ConfigurationDefault is None Baud Rate Word SizeRTS/DTR Line Driver Inactivity State DS62-Network, DS62-MD4 Network/Modem Host Module Stop BitsParity Disconnect Timeguard Default setting is DisabledSerial Port Device Name Connect Port ID EchoManage Users Login Setup MenuAccess Control Change User’s Port Access and Password ADD UserSelect a non-root user and the DS displays Delete User Radius ConfigurationDirect Port Connection Tacacs Configuration Tacacs Network Port Configuration IP Address Subnet MaskCarriage Return Translation Inactivity TimeoutGateway Address Break LengthIP Filter Configuration SSH Host Key GenerationSelect F, Flush Rules to delete all rules. The DS displays Snmp Configuration Read/Write Community String Default is Enabled Web Server ConfigurationDefault is Disabled Default is zero minutesDS Management Internal Alarm ThresholdModule Name External Alarm Threshold Select 1, the DS displaysOutlet Groups Select 6, Delete All Outlet Groups and the DS displays Firmware / Config Download Enable Firmware UpgradeEnable Configuration File Upload Restore Configuration Defaults Get Current Configuration FileDS62-MD4 Modem Configuration Menu Display Configuration Error LogModem Host V90 Modem 9600 None None LO LO Modem Device Name Network Status Status MenuOverall System Status Current Routing Cache Logged UsersMemory Usage Route Setup ProcessesUnitInfo Database Unit ResetLogout Troubleshooting Functional SolutionsDS62 and DS62-MD4 Reset procedure DS62/DS62-MD4BayTech Product Warranty ExceptionsTechnical Support Email support@baytech.netReturn Authorization Process