Bay Technical Associates DS Series, DS62-MD4 Gateway Address, Inactivity Timeout, Break Length

Page 29

DS62-Network, DS62-MD4 Network/Modem Host Module

Select 2) to enter the Subnet Mask followed by <cr>. Failure to enter the address in the decimal form causes the DS to display the following until it is entered correctly. Default Subnet Mask is 0.0.0.0.

Enter Subnet Mask in dotted decimal form :

Gateway Address

The Gateway is the address of a router to connect to other parts of a network. The Gateway address consists of four bytes, each byte ranging from 0 to 255. If your network uses gateways, this parameter must be programmed before the DS can be accessed through the network.

Select 3) to enter the Gateway address. Failure to enter the address in the decimal form causes the DS to display the following until it is entered correctly. Default Gateway address is 0.0.0.0.

Enter Gateway address in dotted decimal form :

Inactivity Timeout

This option enables the DS to disconnect after the programmed amount of time, if there is no activity. Default is 0 (DISABLED). The enabling input can be from 1 to 120 minutes.

Connection Inactivity Timeout is 0 minutes

Enter timeout, in minutes (<=120, 0 to disable) :

Enter 0 to disable or a number between 1 and 120 (inclusive) to set the timeout.

Carriage Return Translation

This option determines what the telnet processor will do with the line-feeds and nulls after a carriage return is sent. Enable tells the DS Telnet processor to strip line feeds or nulls Translation after the carriage returns. Disable allows the characters to pass through. Default is “DISABLED”.

Carriage Return Translation is.... Enabled

Enable ? (Y/N), CR for no change) :

Break Length

Users may configure the DS for a break length of 1 - 1000 milliseconds. In a Telnet session with the DS through the serial port of a DS74, send a Telnet break command (0xF3) to the DS, the serial port will send a break signal of the programmed duration. Default is 350 milliseconds.

Break Length is (msec)

350

Enter break length, in milliseconds (<=10000, 0 to disable) :

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents DS Series Manual DS62-Network, DS62-MD4 Network/Modem Host Module EIA-232 Serial Connection DS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module Internal Modem Connection InstallationConnection Description Quick Start Host Module PowerSerial Setup DS-DS Access Control Login Setup MenuRadius Configuration Network Port ConfigurationAdapters Signals Description DS62 EIA-232 RJ-45 Signal Pin DirectionSignal RS-232 COM Port Port DS Port RPC DE-9 Pin DB-25 Pin CablingAdapters Main Screen Detail Operations and ConfigurationsConfiguration Status Unit Configuration MenuDTR RTS Handshaking Serial Port ConfigurationDefault is None Word Size Baud RateRTS/DTR Line Driver Inactivity State DS62-Network, DS62-MD4 Network/Modem Host Module Stop BitsParity Serial Port Device Name Default setting is DisabledDisconnect Timeguard Connect Port ID EchoManage Users Login Setup MenuAccess Control ADD User Change User’s Port Access and PasswordSelect a non-root user and the DS displays Delete User Radius ConfigurationDirect Port Connection Tacacs Configuration Tacacs Network Port Configuration Subnet Mask IP AddressGateway Address Inactivity TimeoutCarriage Return Translation Break LengthSSH Host Key Generation IP Filter ConfigurationSelect F, Flush Rules to delete all rules. The DS displays Snmp Configuration Read/Write Community String Default is Disabled Web Server ConfigurationDefault is Enabled Default is zero minutesDS Management Internal Alarm ThresholdModule Name Select 1, the DS displays External Alarm ThresholdOutlet Groups Select 6, Delete All Outlet Groups and the DS displays Enable Firmware Upgrade Firmware / Config DownloadEnable Configuration File Upload Get Current Configuration File Restore Configuration DefaultsDisplay Configuration Error Log DS62-MD4 Modem Configuration MenuModem Host V90 Modem 9600 None None LO LO Modem Device Name Network Status Status MenuOverall System Status Current Routing Cache Logged UsersMemory Usage Processes Route SetupUnitInfo Database Unit ResetLogout Functional Solutions TroubleshootingDS62/DS62-MD4 DS62 and DS62-MD4 Reset procedureExceptions BayTech Product WarrantyEmail support@baytech.net Technical SupportReturn Authorization Process
Top Page Image Contents