Bay Technical Associates DS62-MD4, DS Series External Alarm Threshold, Select 1, the DS displays

Page 36

DS62-Network, DS62-MD4 Network/Modem Host Module

Sel M/P

Identifier

Low Curr

1 2/1

DS3ADE

0

Enter the Selection number and the unit will display one of the following dependent on the alarm:

Enter threshold value in tenths of unit measurement (degrees,%,etc.):

Enter voltage threshold value in tenths of a volt:

Enter low current threshold value in tenths of an amp:

NOTE: M/P = Module number and Port number; Identifier = this unit’s model number; Tmp Lvl = temperature level, Lo V Lvl = low voltage level, Hi V Lvl = High voltage level, low Curr

=Low Current. The unit’s firmware determines whether the degrees are Celsius or Fahrenheit. Currently there is no option to change the degrees.

External Alarm Threshold

Selecting the Environmental Sensors with no probes attached the DS will display the following:

None of the installed devices support this option (no temperature probes installed).

Strike ENTER to continue

Selecting the Environmental Sensor with a probe attached the DS will display the following:

Environmental

Sensor Configuration Menu

Sel

M/P

Identifier

1

2/1

DS3ADE

2

All Sensors

Select 1), the DS displays:

Sel

Type

Name

Hi/En

Lo/En

St/En

1

Contact

External Sensor1

N/A

N/A

Ds

2

Temperature External Sensor2

0/Ds

0/Ds

N/A

Enter Request :2

Selecting probe 2 displays a recognized temperature probe:

DS/RPS External Environmental Sensor Configuration Menu

Sensor Number: 2 Name: External Sensor2 Type: Temperature

1...High Threshold (tenths of meas. unit): 0

2...High Threshold Trap Enable: Disabled

3...Low Threshold (tenths of meas. unit): 0

4...Low Threshold Trap Enable: Disabled

Enter Request :1

36

Image 36
Contents DS Series Manual DS62-Network, DS62-MD4 Network/Modem Host Module EIA-232 Serial Connection DS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module Installation Connection DescriptionInternal Modem Connection Power Quick Start Host ModuleSerial Setup DS-DS Login Setup Menu Access ControlNetwork Port Configuration Radius ConfigurationDS62 EIA-232 RJ-45 Signal Pin Direction Adapters Signals DescriptionSignal RS-232 COM Port Port DS Port RPC DE-9 Pin DB-25 Pin CablingAdapters Detail Operations and Configurations Main ScreenUnit Configuration Menu Configuration StatusDTR RTS Serial Port Configuration Default is NoneHandshaking Baud Rate Word SizeDS62-Network, DS62-MD4 Network/Modem Host Module Stop Bits ParityRTS/DTR Line Driver Inactivity State Default setting is Disabled Serial Port Device NameDisconnect Timeguard Connect Port ID EchoLogin Setup Menu Access ControlManage Users Change User’s Port Access and Password ADD UserSelect a non-root user and the DS displays Radius Configuration Direct Port ConnectionDelete User Tacacs Configuration Tacacs Network Port Configuration IP Address Subnet MaskInactivity Timeout Gateway AddressCarriage Return Translation Break LengthIP Filter Configuration SSH Host Key GenerationSelect F, Flush Rules to delete all rules. The DS displays Snmp Configuration Read/Write Community String Web Server Configuration Default is DisabledDefault is Enabled Default is zero minutesInternal Alarm Threshold Module NameDS Management External Alarm Threshold Select 1, the DS displaysOutlet Groups Select 6, Delete All Outlet Groups and the DS displays Firmware / Config Download Enable Firmware UpgradeEnable Configuration File Upload Restore Configuration Defaults Get Current Configuration FileDS62-MD4 Modem Configuration Menu Display Configuration Error LogModem Host V90 Modem 9600 None None LO LO Modem Device Name Status Menu Overall System StatusNetwork Status Logged Users Memory UsageCurrent Routing Cache Route Setup ProcessesUnit Reset LogoutUnitInfo Database Troubleshooting Functional SolutionsDS62 and DS62-MD4 Reset procedure DS62/DS62-MD4BayTech Product Warranty ExceptionsTechnical Support Email support@baytech.netReturn Authorization Process