Bay Technical Associates DS62-MD4, DS Series manual Quick Start Host Module, Power

Page 7

DS62-Network, DS62-MD4 Network/Modem Host Module

PREPARING THE INSTALLATION SITE

The installation area should be clean and free of extreme temperatures and humidity. Allow sufficient space behind the DS unit for cabling and receptacle connections. Access to installation site should be restricted to authorized personnel. Installation of these units should be limited to ITE and Telco server environments.

Power

CAUTION: This unit is intended for indoor use only. Do not install near water or expose this unit to moisture. To prevent heat buildup, do not coil the power cord when in use. Do not use extension cords. Do not attempt to make any internal changes to the power source. Do not attempt to modify any portion or component of a DS-Series Data Switch unless specifically directed to; as in Appendix E of this manual. BayTech must perform any internal changes.

CAUTION: High-voltage surges and spikes can damage this equipment. To protect from such power surges and spikes, this unit must have a good earth ground. A grounding screw connection is located near the power switch on the back of the unit.

CAUTION: Before removing or replacing any modules, turn off main power switch located on the DS-Series Base Unit. Communication to the DS-Series Data Switch will be disrupted while power is off.

CAUTION: For PERMANENTLY CONNECTED EQUIPMENT, a readily accessible disconnect device (Circuit Breaker rated not to exceed the amperage rating of the unit) shall be incorporated in the fixed wiring between the power source and the Baytech unit. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and easily accessible and shall provide back up protection against over current and short circuit by suitable rated protective devices not to exceed the AC current rating for the selected model

QUICK START: HOST Module

by Bay Technical Associates

For those Administrators who have requested the bare minimum for this type of equipment, follow these steps exactly. If this is a new unit shipped directly from Baytech, follow the steps. If this is a previously own unit, perform a factory reset to clear out any users and passwords still in the unit.

Ethernet Controller Configuration:

Before continuing your System Administrator needs to tell you to use DHCP or give you an IP Address, Subnet Address, and Gateway Address.

1.Connect the 9FRJ45PC-4 or 9FRJ45PC-1 adapter to your PC.

2.Connect the supplied rollover flat cable RJ08X007 to the adapter and to the EIA232 serial port on the Baytech HOST Module.

3.Use terminal emulation software to access the unit, (i.e. Microsoft Hyper-terminal). Set the PC serial port configuration to the following: 9600 bps, 8 data bits, 1stop bit and no parity.

4.If you get only a blinking cursor Press ‘Enter’. If still only a blinking cursor, Type 5 semi-colons (;), The Attention Character will not echo on the screen. There is a one second delay before the menu is displayed. You should see a menu similar to (Figure 1).

7

Image 7
Contents DS Series Manual DS62-Network, DS62-MD4 Network/Modem Host Module EIA-232 Serial Connection DS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module Connection Description InstallationInternal Modem Connection Quick Start Host Module PowerSerial Setup DS-DS Access Control Login Setup MenuRadius Configuration Network Port ConfigurationCabling DS62 EIA-232 RJ-45 Signal Pin DirectionAdapters Signals Description Signal RS-232 COM Port Port DS Port RPC DE-9 Pin DB-25 PinAdapters Main Screen Detail Operations and ConfigurationsConfiguration Status Unit Configuration MenuDTR RTS Default is None Serial Port ConfigurationHandshaking Word Size Baud RateParity DS62-Network, DS62-MD4 Network/Modem Host Module Stop BitsRTS/DTR Line Driver Inactivity State Connect Port ID Echo Default setting is DisabledSerial Port Device Name Disconnect TimeguardAccess Control Login Setup MenuManage Users ADD User Change User’s Port Access and PasswordSelect a non-root user and the DS displays Direct Port Connection Radius ConfigurationDelete User Tacacs Configuration Tacacs Network Port Configuration Subnet Mask IP AddressBreak Length Inactivity TimeoutGateway Address Carriage Return TranslationSSH Host Key Generation IP Filter ConfigurationSelect F, Flush Rules to delete all rules. The DS displays Snmp Configuration Read/Write Community String Default is zero minutes Web Server ConfigurationDefault is Disabled Default is EnabledModule Name Internal Alarm ThresholdDS Management Select 1, the DS displays External Alarm ThresholdOutlet Groups Select 6, Delete All Outlet Groups and the DS displays Enable Firmware Upgrade Firmware / Config DownloadEnable Configuration File Upload Get Current Configuration File Restore Configuration DefaultsDisplay Configuration Error Log DS62-MD4 Modem Configuration MenuModem Host V90 Modem 9600 None None LO LO Modem Device Name Overall System Status Status MenuNetwork Status Memory Usage Logged UsersCurrent Routing Cache Processes Route SetupLogout Unit ResetUnitInfo Database Functional Solutions TroubleshootingDS62/DS62-MD4 DS62 and DS62-MD4 Reset procedureExceptions BayTech Product WarrantyEmail support@baytech.net Technical SupportReturn Authorization Process