Option settings
Use the F and G buttons on the projector or remote control unit to select an item, then press the I or
Hbuttons to change the setting.
| OPTION1 | |||
OSD |
|
|
| ON |
AUTO | SIGNAL | ON | ||
AUTO | KEYSTN | ON | ||
AUTO | RGB | IN | ON | |
RGB2 | SELECT | INPUT | ||
|
| |||
RGB/YP B P R | AUTO | |||
VGA60/525P | 525P | |||
SXGA | MODE | SXGA | ||
SELECT |
| ADJ | RETRN | |
| ||||
| OPTION2 | |||
|
|
| ||
BACK | COLOR | BLUE | ||
|
|
|
|
|
FRONT/REAR | FRONT | |||
|
|
|
|
|
DESK/CEILING | DESK | |||
|
|
| ||
FAN | CONTROL | STANDARD | ||
|
|
|
|
|
LAMP | POWER | HIGH | ||
LAMP | RUNTIME | 100H | ||
|
|
|
|
|
FUNC | 1 |
|
| INDEX |
|
|
| ||
CONTROL | KEY | ON | ||
| ||||
AUTO POW . OFF DISABLE | ||||
SELECT |
| ADJ | RETRN | |
OSD
ON
The current input name is displayed in the
OFF
Use this setting when you do not want the current input name to be displayed.
AUTO SIGNAL
This should normally be set to ON.
ON
AUTO SETUP will be carried out automatically when the input signal is changed.
OFF
AUTO SETUP will not function when the input signal is changed.
AUTO KEYSTN
This should normally be set to ON.
ON
During automatic setup, the angle of tilt of the projector is detected and keystone distortion is corrected automatically.
OFF
Use this setting when you do not want automatic keystone correction to be carried out during automatic setup, such as when the screen itself is at an angle.
AUTO RGB IN
This should normally be set to ON.
ON
During automatic setup, the projector selects whichever one of the RGB1 IN or RGB2 IN connectors has a signal being input, and uses that signal for projection. (If a picture is being projected, the signal source is not automatically changed.)
OFF
Use this setting when you do not want the signal source to be changed automatically during automatic setup.
RGB2 SELECT
RGB2 SELECT 
INPUT
[
OUTPUT
This setting is used to select the function of the RGB2 IN/RGB1 OUT connector.
RGB/YPBPR
RGB/YP B P R | AUTO |
| [� |
| RGB |
| [ |
| YP B P R |
This should normally be set to AUTO. RGB or YPBPR is selected automatically depending on the synchronising signal status. When HDTV, 525p (480p), 525i (480i), 625i, 750p, and some VGA480 signals are being input, select “RGB” or “YPBPR” in accordance with the input signal.
VGA60/525P
VGA60/525P 525P
[
VGA60
When a VGA60 or 525p RGB signal is being input, select the signal in accordance with the input signal.
SXGA MODE
SXGA MODE | SXGA |
| [ |
| SXGA+ |
This setting is only for an SXGA signal.
SXGA
Select this item normally.
SXGA+
When the projected image is contracted vertically, select this item.
BACK COLOR
BACK COLOR | BLUE |
| [ |
| BLACK |
This sets the color which is projected onto the screen when no signal is being input to the projector.
FRONT/REAR
FRONT/REAR 
FRONT
[
REAR
This setting should be changed in accordance with the projector
Set to “FRONT” when using a normal reflective screen with the projector positioned in front of the screen, and set to “REAR” when using a translucent screen with the projector positioned behind the screen.
DESK/CEILING
DESK/CEILING 
DESK
[
CEILING
This setting should be changed in accordance with the projector
Set to “DESK” when setting up the projector on a desk or similar, and set to “CEILING” when suspending the projector from the ceiling using the ceiling bracket which is sold separately.
FAN CONTROL
FAN CONTROL 
STANDARD 
[
HIGH
Set FAN CONTROL to “HIGH”, when using this projector at high elevations (above 1400 m) only.
LAMP POWER
LAMP POWER | HIGH |
| [ |
|
|
| LOW |
This setting changes the lamp brightness. When set to “LOW”, the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced.
Adjustments and settings
|
|