NOTE:
BThe entered password will appear as 
. It will not be displayed on the screen.
BIf you enter the wrong password, the letters “PASSWORD” and “NEW” will become red. Enter the correct password again.
TEXT DISPLAY
The setup letters can be displayed at the bottom of the projected image while an image is projected.
ON
TEXT DISPLAY is enabled.
OFF
TEXT DISPLAY is disabled.
TEXT CHANGE
The setup letters which will be displayed when TEXT DISPLAY is set to “ON” can be changed. Press the ENTER button to display the TEXT CHANGE screen.
TEXT CHANGE
ABCDEFGHIJKLMNO PQRSTUVWXYZ0123 456789 @ . :;/+ - 
B S | O K | Cancel |
#Use the F, G, I and H buttons to select the characters, then press the ENTER button. (You can enter 22 characters continuously.)
CPress “BS” on the screen to delete a character.
$Use the F, G, I and H buttons to select “OK”, then press the ENTER button.
CSelect “Cancel” to cancel the change.
When the TEMP indicator and the LAMP indicator are illuminated
There are two indicators on the control panel of the projector which give information about the operating condition of the projector. These indicators illuminate or flash to warn you about problems that have occurred inside the projector, so if you notice that one of the indicators is on, turn off the power and check the table below for the cause of the problem.
LAMP indicator
TEMP indicator
|
| TEMP indicator |
|
|
| |
|
|
|
|
|
|
|
Indicator | Illuminated (red) |
| Flashing (red) | Flashing (red) |
|
|
display | (Lamp unit on) |
| (Lamp unit on) | (Lamp unit off) |
|
|
|
|
|
|
|
|
|
| The surrounding |
| The temperature | The surrounding |
|
|
| temperature or the |
| inside the projector | temperature or the |
|
|
| temperature inside |
| has become | temperature inside |
|
|
| the projector has |
| dangerously high, or | the projector has |
|
|
Problem | become unusually |
| the temperature has | become dangerously |
|
|
| high. |
| suddenly changed. | high, causing the |
|
|
|
|
|
| lamp unit to be |
|
|
|
|
|
| automatically shut |
| maintenance |
|
|
|
| off. |
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
Possible | BThe ventilation holes may be covered. |
|
|
| ||
BThe ambient temperature in the place of use may be too high. |
|
| ||||
cause | BThe air filter may be blocked. |
|
|
| ||
|
|
|
|
|
| and |
| BUncover the ventilation holes. |
|
| |||
|
|
|
| |||
| BSet up the projector in a place where the temperature is |
| Care | |||
| between 20% and 80% (with no condensation). [If you set the |
| ||||
| between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is |
|
| |||
Remedy | FAN CONTROL to “HIGH” (page 43), set up the projector in a |
|
| |||
|
| |||||
place where the temperature is between 0 °C (32 °F) and 35 °C |
|
| ||||
|
|
| ||||
| (95 °F) and the humidity is between 20% and 80% (with no |
|
| |||
| condensation).] |
|
|
|
|
|
| BTurn off the MAIN POWER switch by following the procedure |
|
| |||
| on page 24, and then clean the air filter (refer to page 49). |
|
| |||
|
|
|
|
|
|
|