American Power Conversion PX user manual Rear View of a Power Array

Page 21

Chapter 1 - Physical Representation

Rear View of a Power Array

The rear of a MiniFrame Power Array system is shown be- low. (The rear of a MasterFrame is identical.) Each of the components is described in a section that follows:

System Enable Switch

The system enable switch regulates power to the intelligence modules. It does not power the load. When switched to the “on” position, the Power Array enters the load-disconnect operating mode. When switched to “stand by,” the intelli- gence modules are disconnected from the mains voltage, and the system shuts down.

Note: The load is not powered until the “power the load” com- mand is entered into the PowerView user interface.

Communication Interface Ports

There are three interface ports: A Remote PowerView port for the 6.1 m (20') RJ45 PowerView cable, a 9-pin computer interface port for APC PowerChute Plus software, and a bat- tery communication port for an XR Extended Run Frame.

Smart SlotsTM Accessory Ports

APC manufactures a set of auxiliary user interface accesso- ries, called SmartSlotTM devices. Four SmartSlotTM installa-

Communication

Interface

Ports

Convenience Power

Panel

System

Enable

Switch

XR Extended Run

Battery Frame

Connector

REPO Wiring

Access Panels

tion ports are provided. SmartSlotTM interface options include the following:

nProtection and safe shutdown of multiple servers

nSNMP adaptor for accessing data via a network

nCallUPSTM - telephone notification of power event

nMeasureUPSTM - monitor environmental conditions

nControl and monitor Power Array via modem Note: Use only SmartSlotTM devices labeled “SymmetraTM Compatible.”

REPO/Input/Output Wiring Access Panels

Wiring terminal blocks for input and output wiring and for remote emergency power off (REPO) switch installations are accessed through these panels.

Note: Wiring is to be installed by a qualified electrician only.

Convenience Power Panel

Eight IEC 320 C13 type power outlets are provided. The out- lets are arranged in two sets of four. Each set is equipped with a circuit breaker.

Extended Run Battery Frame Connector

An optional XR Extended Run Battery Frame can be connected to the Power Array via this connector. See the User’s Manual included with the XR Extended Run Battery Frame.

SmartSlotTM

Accessory

Ports

MiniFrame

Output

Wiring

Access

Panels

Input

Wiring

Access

Panels

Fig 1-10 Rear View of a Mini Frame SymmetraTM Power Array System

1-4

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Page +353 91 Main Tech SupportToll-Free Numbers 0660Radio Frequency Interference Important Safety InstructionsLife Support Policy Limited WarrantyTable of Contents Index MiniFrame MasterFrame IntroductionFig I-2 Functional Diagram of a SymmetraTM Power Processing Battery SourceThank You SymmetraTM Overview Theory of OperationPower Processing System Battery SourceControl/User Interface Load-Disconnect Mode On-Line Operating ModeModes of Operation Bypass Operating Mode On-Battery Operating ModeImportant Information DefinitionsPage Important Safety Information Safety InformationSafety Earth Ground Indicates the pri- mary safety ground Symbols Used In This ManualSafety-2 Physical Representation Five Four Power Battery Power Array FrameModule BaysPower Module Powerview User InterfaceBattery Module Power ModuleMain Intelligence Module MIM Maintenance Bypass SwitchRedundant Intelligence Module RIM Input Circuit BreakerRear View of a Power Array Site Preparation Transporting Power Array to Installation Site Space and Weight ConsiderationsOperating Conditions BTU OutputSite Preparation Unpacking and Installing Frame Initial Inspection Dimensions WeightMove the Frame Check For DamageMoving Battery & Power Modules Remove Packing MaterialsRemove the Frame from the Pallet Wiring Requirements & Procedures Input Wiring SymmetraTM WiringOutput Wiring Repo Switch WiringInput Wiring Input Wiring SpecificationsInput Wiring Procedures Ground Wiring and Input Wiring Terminal Blocks Ground Wiring Terminal BlockOutput Wiring Installation Output WiringRepo Specifications Remote Emergency Power Off SwitchRepo Switch Installation Cable SpecificationsElectrical Wiring Test/Checklist Electrical Wiring TestContact Closure Repo Switch Connection Vdc Repo Switch Connection11 Startup Screen Record the PowerView reportedSetting Up The Power Array Frame Leveling Procedure Setup of Power ArrayRemoving Grill Covers PositionsProcedure for Battery Module Installation Installing the Battery ModulesClear all battery module bays of any debris Battery Module Location of Battery Module BaysProcedure for Power Module Installation Installing the Power ModulesInstalling the Redundant Intelligence Module RIM Installing the Main Intelligence Module MIMMain Intelligence Module 10 Location of the MIM and RIMRemote Placement of the PowerView Installing the PowerView InterfaceWall Mounting the PowerView Remove the grill cover from the top level of the frameSmartSlotTM Interface Accessories Installation Test/Checklist Installation TestPower Reported SymmetraTM Power Module/Frame Capacities21 Miscellaneous Status Screen 22 Power The Load Sequence 25 Return to On-Line Mode System Setup PowerView Display Physical Features of the Powerview PowerView FunctionsPowerView Interface Symbol Name Function of Key On Key PowerView LED IndicatorsEsc Navigation KeysTop-Level Menu Screen Startup ScreenControl StatusAccessories SetupDiagnostics LoggingConfiguring & Operating the SymmetraTM Introduction Powering the Power ArrayReview Status Conditions Powering the LoadsVoltage Status Screen Load With No Redundancy Status ScreenLoad With Redundancy Status Screen Battery Status Screen Power Status ScreenFrequency Status Screen 11 Sample Alarm Threshold Status Screen Alarm Threshold Status ScreenPerform a Self Test Miscellaneous Status ScreenAlarm Thresholds Selection Screen Configure AlarmsSwitching Audible Alarm Beeper Off Shutdown Parameter Selection ScreenDiagnostics Menu Screen Review Diagnostic InformationReview Logging Menu Event Log ScreenModule Replacement Module Replacement Module Failure Alarm IndicatorsReturning Modules to APC Battery Module Replacement Installing the Replacement ModuleReplacement Battery Module Verification Power Module Replacement Replacement Module VerificationRefer to for the power module installation proce- dure Installing the Replacement Main Intelligence Module Redundant Intelligence Module ReplacementReplacement MIM Verification Installing the Replacement Redundant Intelligence ModulePowerView Interface Messages PowerView Meaning Corrective Action Message Start-Up MIM detects the RIM beforeRIM is awake # of batteries decreased PowerView Meaning Corrective Action MessageLoad is No Longer above Has been corrected either becauseThreshold. Startup-Setup-Alarms Setup-Alarms-RedundancySelect zero Redundancy-selectBecause of a power failure, wait for Battery modules are beingSupport. See inside front cover PowerView Display Messages Index Configuring PowerView Threshold status Electro-static discharge, 2-1 Emergency power offDescription Description, 1-4 Installation Ordering information ConfiguringChecklist Input Output Overview Repo Frame, 2-1 ModulesReplacement Modules & Accessories English Text
Top Page Image Contents