American Power Conversion PX user manual Limited Warranty, Life Support Policy

Page 4

Limited Warranty

American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of one year from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization (RMA) number from APC or an APC service center. Products must be returned to APC or an APC service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been damaged by accident, negligence, or mis-application or has been altered or modified in any way. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase.

EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBIL- ITY OF SUCH DAMAGE. Specifically, APC is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Life Support Policy

As a general policy, American Power Conversion (APC) does not recommend the use of any of its products in life support appli- cations where failure or malfunction of the APC product can be reasonably expected to cause failure of the life support device or to significantly affect its safety or effectiveness. APC does not recommend the use of any of its products in direct patient care. APC will not knowingly sell its products for use in such applications unless it receives in writing assurances satisfactory to APC that (a) the risks of injury or damage have been minimized, (b) the customer assumes all such risks, and (c) the liability of American Power Conversion is adequately protected under the circumstances.

Examples of devices considered to be life support devices are neonatal oxygen analyzers, nerve stimulators (whether used for anesthesia, pain relief, or other purposes), autotransfusion devices, blood pumps, defibrillators, arrhythmia detectors and alarms, pacemakers, hemodialysis systems, peritoneal dialysis systems, neonatal ventilator incubators, ventilators for both adults and in- fants, anesthesia ventilators, infusion pumps, and any other device designated as “critical” by the U.S.F.D.A.

Hospital grade wiring devices and leakage current may be ordered as options on many APC UPS systems. APC does not claim that units with this modification are certified or listed as Hospital Grade by APC or any other organization. Therefore these units do not meet the requirements for use in direct patient care.

Entire contents copyright © 1998 American Power Conversion. All rights reserved; reproduction in whole or in part without permission is prohibited. Symmetra, Power Array, SmartSlot, SmartCell and SNMP Adapter are trademarks of APC. Power- Chute and PowerDoctor are registered trademarks of APC. All other trademarks are the property of their respective owners.

Image 4
Contents Page Main Tech Support +353 91Toll-Free Numbers 0660Important Safety Instructions Radio Frequency InterferenceLimited Warranty Life Support PolicyTable of Contents Index Introduction MiniFrame MasterFramePower Processing Battery Source Fig I-2 Functional Diagram of a SymmetraTMThank You SymmetraTM Overview Theory of OperationBattery Source Power Processing SystemControl/User Interface On-Line Operating Mode Load-Disconnect ModeModes of Operation On-Battery Operating Mode Bypass Operating ModeDefinitions Important InformationPage Safety Information Important Safety InformationSymbols Used In This Manual Safety Earth Ground Indicates the pri- mary safety groundSafety-2 Physical Representation Power Array Frame Five Four Power BatteryModule BaysPowerview User Interface Power ModuleBattery Module Power ModuleMaintenance Bypass Switch Main Intelligence Module MIMRedundant Intelligence Module RIM Input Circuit BreakerRear View of a Power Array Site Preparation Space and Weight Considerations Transporting Power Array to Installation SiteOperating Conditions BTU OutputSite Preparation Unpacking and Installing Frame Dimensions Weight Initial InspectionMove the Frame Check For DamageRemove Packing Materials Moving Battery & Power ModulesRemove the Frame from the Pallet Wiring Requirements & Procedures SymmetraTM Wiring Input WiringOutput Wiring Repo Switch WiringInput Wiring Specifications Input WiringInput Wiring Procedures Ground Wiring Terminal Block Ground Wiring and Input Wiring Terminal BlocksOutput Wiring Output Wiring InstallationRemote Emergency Power Off Switch Repo SpecificationsRepo Switch Installation Cable SpecificationsElectrical Wiring Test Electrical Wiring Test/ChecklistContact Closure Repo Switch Connection Vdc Repo Switch ConnectionRecord the PowerView reported 11 Startup ScreenSetting Up The Power Array Setup of Power Array Frame Leveling ProcedureRemoving Grill Covers PositionsInstalling the Battery Modules Procedure for Battery Module InstallationClear all battery module bays of any debris Battery Module Location of Battery Module BaysInstalling the Power Modules Procedure for Power Module InstallationInstalling the Main Intelligence Module MIM Installing the Redundant Intelligence Module RIMMain Intelligence Module 10 Location of the MIM and RIMInstalling the PowerView Interface Remote Placement of the PowerViewWall Mounting the PowerView Remove the grill cover from the top level of the frameSmartSlotTM Interface Accessories Installation Test Installation Test/ChecklistSymmetraTM Power Module/Frame Capacities Power Reported21 Miscellaneous Status Screen 22 Power The Load Sequence 25 Return to On-Line Mode System Setup PowerView Display PowerView Functions Physical Features of the PowerviewPowerView Interface PowerView LED Indicators Symbol Name Function of Key On KeyEsc Navigation KeysStartup Screen Top-Level Menu ScreenControl StatusSetup AccessoriesDiagnostics LoggingConfiguring & Operating the SymmetraTM Powering the Power Array IntroductionPowering the Loads Review Status ConditionsVoltage Status Screen Load With No Redundancy Status ScreenPower Status Screen Load With Redundancy Status Screen Battery Status ScreenFrequency Status Screen Alarm Threshold Status Screen 11 Sample Alarm Threshold Status ScreenPerform a Self Test Miscellaneous Status ScreenConfigure Alarms Alarm Thresholds Selection ScreenSwitching Audible Alarm Beeper Off Shutdown Parameter Selection ScreenReview Diagnostic Information Diagnostics Menu ScreenReview Logging Menu Event Log ScreenModule Replacement Module Failure Alarm Indicators Module ReplacementReturning Modules to APC Installing the Replacement Module Battery Module ReplacementReplacement Battery Module Verification Replacement Module Verification Power Module ReplacementRefer to for the power module installation proce- dure Redundant Intelligence Module Replacement Installing the Replacement Main Intelligence ModuleReplacement MIM Verification Installing the Replacement Redundant Intelligence ModulePowerView Interface Messages MIM detects the RIM before PowerView Meaning Corrective Action Message Start-UpRIM is awake PowerView Meaning Corrective Action Message # of batteries decreasedLoad is No Longer above Has been corrected either becauseSetup-Alarms-Redundancy Threshold. Startup-Setup-AlarmsSelect zero Redundancy-selectBattery modules are being Because of a power failure, wait forSupport. See inside front cover PowerView Display Messages Index Electro-static discharge, 2-1 Emergency power off Configuring PowerView Threshold statusDescription Configuring Description, 1-4 Installation Ordering informationChecklist Input Output Overview Repo Frame, 2-1 ModulesReplacement Modules & Accessories English Text