American Power Conversion PX user manual Installing the Main Intelligence Module MIM

Page 40

Chapter 5 - System Setup

Installing the Main Intelligence Module (MIM)

The main intelligence module is factory installed. The fol- lowing procedure is provided in the event that the MIM is removed or replaced:

Note: The main intelligence module is installed in the upper right bay of the Power Array frame. The main intelligence mod- ule is always installed in the bottom rack in this bay, and the redundant intelligence module is always installed in the top rack in this bay.

1.Carefully align the installation rail on the MIM with the track that runs along the inside of the bay.

2.Slide the MIM into the bay.

3.Tighten the two retaining screws. Do not overtighten.

4.Swing the flip latch into place, and tighten the screw. Do

not overtighten this screw. See figure 5-9.

Redundant

Intelligence

Module

(RIM)

Main

Intelligence

Module

(MIM)

Fig 5-10 Location of the MIM and RIM

Installing the Redundant Intelligence Module (RIM)

The redundant intelligence module is factory installed. The following procedure is provided in the event that the RIM is removed or replaced:

Note: The redundant intelligence module is installed in the up- per right bay of the Power Array frame. The redundant intelli- gence module is always installed in the top rack in this bay, and the main intelligence module is always installed in the bottom rack in this bay.

1.Carefully align the installation rail on the RIM with the track that runs along the inside of the bay.

2.Slide the RIM into the bay.

3.Tighten the two retaining screws. Do not overtighten.

4.Swing the flip latch into place, and tighten the screw. Do not overtighten this screw. See figure 5-9.

5-4

Image 40

Contents Page Main Tech Support +353 91Toll-Free Numbers 0660Important Safety Instructions Radio Frequency InterferenceLimited Warranty Life Support PolicyTable of Contents Index Introduction MiniFrame MasterFramePower Processing Battery Source Fig I-2 Functional Diagram of a SymmetraTMThank You SymmetraTM Overview Theory of OperationBattery Source Power Processing SystemControl/User Interface On-Line Operating Mode Load-Disconnect ModeModes of Operation On-Battery Operating Mode Bypass Operating ModeDefinitions Important InformationPage Safety Information Important Safety InformationSymbols Used In This Manual Safety Earth Ground Indicates the pri- mary safety groundSafety-2 Physical Representation Power Array Frame Five Four Power BatteryModule BaysPowerview User Interface Power ModuleBattery Module Power ModuleMaintenance Bypass Switch Main Intelligence Module MIMRedundant Intelligence Module RIM Input Circuit BreakerRear View of a Power Array Site Preparation Space and Weight Considerations Transporting Power Array to Installation SiteOperating Conditions BTU OutputSite Preparation Unpacking and Installing Frame Dimensions Weight Initial InspectionMove the Frame Check For DamageRemove Packing Materials Moving Battery & Power ModulesRemove the Frame from the Pallet Wiring Requirements & Procedures SymmetraTM Wiring Input WiringOutput Wiring Repo Switch WiringInput Wiring Specifications Input WiringInput Wiring Procedures Ground Wiring Terminal Block Ground Wiring and Input Wiring Terminal BlocksOutput Wiring Output Wiring InstallationRemote Emergency Power Off Switch Repo SpecificationsRepo Switch Installation Cable SpecificationsElectrical Wiring Test Electrical Wiring Test/ChecklistContact Closure Repo Switch Connection Vdc Repo Switch ConnectionRecord the PowerView reported 11 Startup ScreenSetting Up The Power Array Setup of Power Array Frame Leveling ProcedureRemoving Grill Covers PositionsInstalling the Battery Modules Procedure for Battery Module InstallationClear all battery module bays of any debris Battery Module Location of Battery Module BaysInstalling the Power Modules Procedure for Power Module InstallationInstalling the Main Intelligence Module MIM Installing the Redundant Intelligence Module RIMMain Intelligence Module 10 Location of the MIM and RIMInstalling the PowerView Interface Remote Placement of the PowerViewWall Mounting the PowerView Remove the grill cover from the top level of the frameSmartSlotTM Interface Accessories Installation Test Installation Test/ChecklistSymmetraTM Power Module/Frame Capacities Power Reported21 Miscellaneous Status Screen 22 Power The Load Sequence 25 Return to On-Line Mode System Setup PowerView Display PowerView Functions Physical Features of the PowerviewPowerView Interface PowerView LED Indicators Symbol Name Function of Key On KeyEsc Navigation KeysStartup Screen Top-Level Menu ScreenControl StatusSetup AccessoriesDiagnostics LoggingConfiguring & Operating the SymmetraTM Powering the Power Array IntroductionPowering the Loads Review Status ConditionsVoltage Status Screen Load With No Redundancy Status ScreenPower Status Screen Load With Redundancy Status Screen Battery Status ScreenFrequency Status Screen Alarm Threshold Status Screen 11 Sample Alarm Threshold Status ScreenPerform a Self Test Miscellaneous Status ScreenConfigure Alarms Alarm Thresholds Selection ScreenSwitching Audible Alarm Beeper Off Shutdown Parameter Selection ScreenReview Diagnostic Information Diagnostics Menu ScreenReview Logging Menu Event Log ScreenModule Replacement Module Failure Alarm Indicators Module ReplacementReturning Modules to APC Installing the Replacement Module Battery Module ReplacementReplacement Battery Module Verification Replacement Module Verification Power Module ReplacementRefer to for the power module installation proce- dure Redundant Intelligence Module Replacement Installing the Replacement Main Intelligence ModuleReplacement MIM Verification Installing the Replacement Redundant Intelligence ModulePowerView Interface Messages MIM detects the RIM before PowerView Meaning Corrective Action Message Start-UpRIM is awake PowerView Meaning Corrective Action Message # of batteries decreasedLoad is No Longer above Has been corrected either becauseSetup-Alarms-Redundancy Threshold. Startup-Setup-AlarmsSelect zero Redundancy-selectBattery modules are being Because of a power failure, wait forSupport. See inside front cover PowerView Display Messages Index Electro-static discharge, 2-1 Emergency power off Configuring PowerView Threshold statusDescription Configuring Description, 1-4 Installation Ordering informationChecklist Input Output Overview Repo Frame, 2-1 ModulesReplacement Modules & Accessories English Text