Panasonic WJ-FS616C manual Alarm Control Function, Alarm Input, Alarm Operation

Page 59

ALARM CONTROL FUNCTION

The alarm function activates the warning alarm status, when an externally connected alarm sensor is turned on. Described below is an example of an alarm status activa- tion.

Alarm Input

The video multiplexer can handle the following alarms:

Interface Alarm

Alarm received from the ALARM/REMORTE port on the rear of the multiplexer.

“ALARM” is displayed on the monitor screen.

Video Input Signal Loss Alarm

Alarm indicating that a camera video signal loss has occurred.

“CH✽✽LOSS” is displayed on the monitor screen.

Camera Site Alarm

Alarm received from the associated camera site receiv- er or camera.

“ALARM” is displayed on the monitor screen.

PC Command Alarm

OAI command received from the Personal Computer. “ALARM” is displayed on the monitor screen.

Alarm Operation

When an alarm signal is received, the multiplexer, the Record Output, Spot Output and Multiscreen Output of the multiplexer are activated as shown below.

Refer to the ALARM SETUP menu of the WJ-FS616C SETUP MENU for further settings.

Front Panel Display

When an alarm function is activated, the ALARM Indicator (Red) and the corresponding CAMERA (1 – 16) button (Green) blink.

The Alarm Output signal is supplied to pin 9 of the ALARM/ REMOTE port for the programmed duration.

After the programmed time has elapsed, the indicator changes to a steady light.

If another alarm is activated during output of the previous alarm, the alarm signal is output for the programmed dura- tion.

Alarm Buzzer

The buzzer beeps for the programmed duration.

The buzzer stops beeping before that duration when the alarm is reset.

Alarm Log

There are 100 alarm records stored in chronological order in 10 pages of table.

If more than 100 alarms are received, the oldest record is overwritten.

The tables also indicate the alarm mode.

Camera Preset Movement

Enables movement of the camera to the preset position that was specified in the ALARM TERMINAL SETUP table of the SYSTEM SETUP menu.

Record Output

Alarms are recorded in the mode specified for the ALM REC MODE parameter in the ALARM SETUP menu.

Alarmed channels are recorded preferentially over other video input if ON is specified for the DYNAMIC REC parameter in the ALARM SETUP menu.

59

Image 59
Contents Operating Instructions Lightning flash with arrowhead symbol Important Safety Instructions Contents Preface FeaturesDo not attempt to disassemble the appliance PrecautionsFully charge up the backup battery Do not drop metallic parts through slotsAlarm Indicator Alarm Power Switch Power ON/OFFLock Indicator Lock Alarm Reset Button ResetMultiscreen Monitor Button Multiscreen Camera Number Buttons Camera Preset Position Number Buttons@2Preset Position Button PRE-POSI Spot Monitor Button SpotLeft Left Right Right @7Auto Button Auto #1Setup/Escape Button SET UP/ESC#2Lock Switch Lock OFF/ON @6Direction Buttons UP/DOWN/LEFT/RIGHT$5Line Selection Switch Line SELECT, 2/4 $1Camera Output Connectors Camera OUT$2Camera Input Connectors Camera $4Line Termination Switch TERM., OFF/ON8Data Port DATA, OUT/IN Installing the WV-PB6164 Data Multiplex Boards InstallationTally Output Setting Dummy Black Image Setting DIP Switch SettingAlarm Output Setting Mounting into the Rack Shown below is an example of a basic system connection ConnectionsConnection with the Camera Sites Connections for RS-485 type camera RS-232C Connection with the MonitorsConnection with the PC Data portConnection with External Remote Control Switches Connection with Alarm SensorsSpot and Multiscreen Monitor Monitors and DisplaysConnect the time lapse VCR as shown in the example below Connection with the Time Lapse VCRSetup Procedures Displaying the Setup Menu Setup MenuSetup Menu Programming Setup MenuAlarm Schedule Alarm SetupAlarm Recall Alarm Display on the Monitors Camera Site AlarmVideo Loss Alarm Camera Switching Pulse Loss AlarmDwell Time for Alarm Sequence Alarm Mode on the Multiscreen MonitorAlarm Mode on the Spot Monitor Alarm Recording ModeStill Display Multiscreen Output SetupCamera Title Display Clock DisplaySecret View Camera Display Position SettingSequence Mode Spot Output Setup Clock Display Record or Multiscreen 2 Output SetupRecord Output Setup Camera Title DisplayDynamic Recording Recording Mode SetupRecording Mode Setting Details Multiscreen 2 Output Setup Camera Display Position Sequence ModeClock Display Position System SetupClock Setup Spot Sequence SEQ1 Camera Title SetupSequence Setup Camera Title Display PositionDwell Time Uniform Dwell Time Preset PositionAuto Skip Image AssignmentDwell Time Multi Sequence SEQ2, SEQ3Camera/Playback Programming Steps 2 to Lock ModeSequence Timing Multiscreen Monitor Sequence Timing Spot MonitorCable Compensation/VD2/Data Alarm Terminal SetupCommunication Port Setup Playback ModeData Mode RS-232C ModeUnit Address Daisy ModeVCR Input Select Password Registration PasswordCamera Upload Other Setup MenusCamera Download All Reset Operating Procedures Single Spot Live Controlling the Video Input and MonitorsSelecting the Spot Monitor Single Sequence LiveFreezing Single Spot Live Selecting the Multiscreen MonitorControlling the Camera Images Single Spot LiveFreezing Multiscreen Spot Live Zooming Single Spot LiveMultiscreen Spot Live Single or Multi Sequence Live Controlling the Playback ImagesFreezing Single Spot Playback Single Spot PlaybackSingle or Multi Sequence Playback Zooming Single Spot PlaybackMultiscreen Spot Playback Freezing Multiscreen Spot PlaybackMultiscreen Spot Live Images with a Playback Image Displaying the Camera and Playback ImagesFreezing Multiscreen Spot Live Images with a Playback Image Lens Control Controlling Camera Site AccessoriesCamera Control Function Camera SelectionPan/Tilt Control Auto Panning Pan/Tilt Control Preset OperationCamera Setup Pan/Tilt Control Home PositionSimplified preset position setting Alarm Operation Alarm Control FunctionAlarm Input Spot Output Multiscreen OutputExample of Using Multiscreen 2 Monitor Alarm ResetReset Spot Alarm SuspensionRecording on the Time Lapse VCR Camera Switching Pulse Loss DisplayOther Function Operating Procedures with WV-CU550C Major Operating Controls and Their Functions System Controller WV-CU550C5Preset Position Button PRE-POSI Busy Indicator BusySet Up button SET UP D Time Lapse Mode Buttons T/L MODE, D C@6Mode Selection switch Mode @2Alarm Reset button Reset@4Termination switch TERM., ON/OFF @5Controller Unit Number switch Controller Unit noConnection with the WV-CU550C System Controller InstallationsModifying the Front Panel WJ-FS616C WV-CU550C Function Setup Menu Operations with WV-CU550CControlling the Video Input and Monitors Function Operations with WV-CU550CCamera Control Function RES A.RES Auxiliary Control Alarm Control FunctionSystem Expansion Application Operating ProcedureConnections Other ApplicationsFor Main Site For Local SiteCommunication Protocol Transmission CommandResponse Command AppendixTransmission Response Parameter Ascii Command Ascii Command TableTable below 19 kinds None QOPResponse Command Ascii Main Unit Information Standard Accessories SpecificationsPanasonic Canada Inc