Panasonic WJ-FS616C Busy Indicator Busy, Function buttons F1/F2/F3/F4, Direction buttons a D B C

Page 66

qAlarm Indicator (ALARM)

This indicator (Red) lights to indicate that an alarm con- dition exists.

It goes off when the alarm is reset automatically.

To turn the ALARM indicator off of the multiplexer, press the RESET button.

wBusy Indicator (BUSY)

This indicator lights to indicate that the system is locked by PC command.

While this indicator is lit, control from the video multi- plexer and system controller is disabled.

eFunction buttons (F1/F2/F3/F4)

Selects functions displayed on the LCD (Liquid Crystal Display) display.

F1: Operates the multiscreen monitor.

F2: Operates the spot monitor.

F3: Activates the sequence mode.

In this mode, a series of camera images is dis- played in succession on the monitor screen for the specified duration.

F4: Selects the camera image or VCR playback image to be displayed on the monitor screen.

rLCD (Liquid Crystal Display) display Displays the function menu and function status.

In this Instructions Manual, it is hereafter referred to as the “LCD”.

tDirection buttons (A D B C)

These buttons function as shown below.

Camera Set On button (CAMERA SET ON A)

This button is used to display the camera setup menu on the monitor screen.

Set Up button (SET UP D)

This button is used to display the setup menu of the video multiplexer.

Camera Set Off button (CAMERA SET OFF B)

This button is used to exit the camera setup menu dis- played on the monitor screen.

Time Lapse Mode Buttons (T/L MODE, D C)

These buttons, in combination with the Alternate button, select the time lapse mode of the time lapse VCR. Press the D button to increase the recording duration or the C button to decrease the recording duration.

Reverse Play button (REV A)

This button, in combination with the Alternate button, activates reverse playback on the time lapse VCR.

Play button (PLAY B)

This button, in combination with the Alternate button, activates playback on the time lapse VCR.

yJoystick Controller

The joystick is used to manually operate the Pan/Tilt Head, move the cursor position in the setup menu of the video multiplexer, or to select an area for Electronic Zooming.

UP: Upward

DOWN: Downward

LEFT: Left

RIGHT: Right

uIris Buttons (IRIS, CLOSE/OPEN)

Close or open the lens iris of cameras equipped with the specified lens.

When these buttons are pressed at the same time, the lens iris is reset to the factory default settings.

iFocus button (FOCUS, NEAR/FAR)

Adjusts the lens focus of cameras equipped with the specified lens.

oZoom button (ZOOM, TELE/WIDE)

Adjusts the lens zoom of cameras equipped with the specified lens.

!0Auto Focus button (AF)

This button is used to activate the auto focus function when the camera equips with the specific feature.

!1Camera (Set) key [CAM(SET)]

CAM: Used for camera selection. To select a camera, enter the desired camera number with the Numeric keys, and then press the CAM key.

SET: While displaying the setup menu on the monitor, pressing this button will execute the currently high- lighted selection and to enter a submenu in the setup menu if the item has its own setting menu.

!2Numeric keys (0-9)

These keys are used for numeric input into the system, such as the camera number, preset position, etc.

!3Monitor (Unit/Escape) key [MON(UNIT/ESC)]

This key is used to select a unit of video multiplexer. Select a unit number with the Numeric key, then press this key to select a specific Video multiplexer.

This key is also used to execute the settings and return to the previous menu in the setup menu of the video multiplexer.

!4Still button (STILL)

This button is used to freeze the image currently dis- played on the monitor screen.

!5Preset Position Button (PRE-POSI)

This button is used to assign a preset position to a specified camera.

67

Image 66
Contents Operating Instructions Lightning flash with arrowhead symbol Important Safety Instructions Contents Features PrefaceDo not drop metallic parts through slots PrecautionsFully charge up the backup battery Do not attempt to disassemble the applianceAlarm Reset Button Reset Power Switch Power ON/OFFLock Indicator Lock Alarm Indicator AlarmSpot Monitor Button Spot Camera Number Buttons Camera Preset Position Number Buttons@2Preset Position Button PRE-POSI Multiscreen Monitor Button Multiscreen@6Direction Buttons UP/DOWN/LEFT/RIGHT #1Setup/Escape Button SET UP/ESC#2Lock Switch Lock OFF/ON Left Left Right Right @7Auto Button Auto$4Line Termination Switch TERM., OFF/ON $1Camera Output Connectors Camera OUT$2Camera Input Connectors Camera $5Line Selection Switch Line SELECT, 2/48Data Port DATA, OUT/IN Installation Installing the WV-PB6164 Data Multiplex BoardsTally Output Setting DIP Switch Setting Alarm Output SettingDummy Black Image Setting Mounting into the Rack Connections Shown below is an example of a basic system connectionConnection with the Camera Sites Connections for RS-485 type camera Data port Connection with the MonitorsConnection with the PC RS-232CConnection with Alarm Sensors Connection with External Remote Control SwitchesMonitors and Displays Spot and Multiscreen MonitorConnection with the Time Lapse VCR Connect the time lapse VCR as shown in the example belowSetup Procedures Setup Menu Displaying the Setup MenuProgramming Setup Menu Setup MenuAlarm Setup Alarm RecallAlarm Schedule Camera Switching Pulse Loss Alarm Camera Site AlarmVideo Loss Alarm Alarm Display on the MonitorsAlarm Recording Mode Alarm Mode on the Multiscreen MonitorAlarm Mode on the Spot Monitor Dwell Time for Alarm SequenceClock Display Multiscreen Output SetupCamera Title Display Still DisplayCamera Display Position Setting Sequence ModeSecret View Spot Output Setup Camera Title Display Record or Multiscreen 2 Output SetupRecord Output Setup Clock DisplayRecording Mode Setup Recording Mode Setting DetailsDynamic Recording Multiscreen 2 Output Setup Sequence Mode Camera Display PositionSystem Setup Clock SetupClock Display Position Camera Title Display Position Camera Title SetupSequence Setup Spot Sequence SEQ1Image Assignment Preset PositionAuto Skip Dwell Time Uniform Dwell TimeMulti Sequence SEQ2, SEQ3 Camera/PlaybackDwell Time Sequence Timing Spot Monitor Lock ModeSequence Timing Multiscreen Monitor Programming Steps 2 toAlarm Terminal Setup Cable Compensation/VD2/DataRS-232C Mode Playback ModeData Mode Communication Port SetupDaisy Mode VCR Input SelectUnit Address Password Password RegistrationOther Setup Menus Camera DownloadCamera Upload All Reset Operating Procedures Single Sequence Live Controlling the Video Input and MonitorsSelecting the Spot Monitor Single Spot LiveSingle Spot Live Selecting the Multiscreen MonitorControlling the Camera Images Freezing Single Spot LiveZooming Single Spot Live Multiscreen Spot LiveFreezing Multiscreen Spot Live Controlling the Playback Images Single or Multi Sequence LiveSingle Spot Playback Freezing Single Spot PlaybackFreezing Multiscreen Spot Playback Zooming Single Spot PlaybackMultiscreen Spot Playback Single or Multi Sequence PlaybackDisplaying the Camera and Playback Images Multiscreen Spot Live Images with a Playback ImageFreezing Multiscreen Spot Live Images with a Playback Image Camera Selection Controlling Camera Site AccessoriesCamera Control Function Lens ControlPan/Tilt Control Home Position Pan/Tilt Control Preset OperationCamera Setup Pan/Tilt Control Auto PanningSimplified preset position setting Alarm Control Function Alarm InputAlarm Operation Multiscreen Output Spot OutputAlarm Reset Example of Using Multiscreen 2 MonitorAlarm Suspension Reset SpotCamera Switching Pulse Loss Display Other FunctionRecording on the Time Lapse VCR Operating Procedures with WV-CU550C System Controller WV-CU550C Major Operating Controls and Their FunctionsTime Lapse Mode Buttons T/L MODE, D C Busy Indicator BusySet Up button SET UP D 5Preset Position Button PRE-POSI@5Controller Unit Number switch Controller Unit no @2Alarm Reset button Reset@4Termination switch TERM., ON/OFF @6Mode Selection switch ModeInstallations Modifying the Front PanelConnection with the WV-CU550C System Controller Setup Menu Operations with WV-CU550C WJ-FS616C WV-CU550C FunctionFunction Operations with WV-CU550C Controlling the Video Input and MonitorsCamera Control Function RES A.RES Alarm Control Function Auxiliary ControlSystem Expansion Other Applications Operating ProcedureConnections ApplicationFor Local Site For Main SiteAppendix Transmission CommandResponse Command Communication ProtocolCommand Table Transmission Response Parameter Ascii Command AsciiQOP Table below 19 kinds NoneResponse Command Ascii Main Unit Information Specifications Standard AccessoriesPanasonic Canada Inc