Panasonic WJ-FS616C manual Other Function, Recording on the Time Lapse VCR

Page 63

OTHER FUNCTION

Recording on the Time Lapse VCR

The following selections are made in the WJ-FS616C SETUP MENU described previously.

Refer to the Recording Mode Setup on page 33 for further details.

1.Check the selected recording mode (MODE 0 - MODE 9).

MODE 0: Normal Mode (Real Time)

MODE 1 - 9: Time Lapse Mode (Linear Mode)

If MODE 9 is selected, check the image (spot or quad) to be recorded on the VCR.

2.Press the Record button of the VCR to begin recording.

Notes:

To let the VCR display the VCR menu for setup, select MODE 0 in the REC MODE SETUP menu of the multiplexer.

While recording with the camera switching pulse (MODE 9), quad recording will work properly when the selected recording interval is more than 0.11 seconds (less than 9 fields/s).

While recording without the camera switching pulse (MODE 1 – 8), quad recording is not available. When using a VCR whose recording interval is 2 or 3 fields, select 4 fields (minimum) for the REC MODE parameter.

However the same image may be recorded repeat- edly.

Camera Switching Pulse Loss Display

When loss of the camera switching pulse is detected, “SW LOSS” will blink on the monitor screen.

The buzzer does not beep.

When the camera switching pulse is recovered, “SW LOSS” is cleared from the monitor.

Notes:

When MODE 0 to MODE 8 is selected for recording, or MULTI2 OUTPUT for REC/ MULTI2, “SW LOSS” is not displayed because of the way the system application works.

If “ALARM” or “CH✽✽LOSS” is displayed on the monitor screen, “SW LOSS” is not displayed because alarm has priority.

63

Image 63
Contents Operating Instructions Lightning flash with arrowhead symbol Important Safety Instructions Contents Preface FeaturesDo not attempt to disassemble the appliance PrecautionsFully charge up the backup battery Do not drop metallic parts through slotsAlarm Indicator Alarm Power Switch Power ON/OFFLock Indicator Lock Alarm Reset Button ResetMultiscreen Monitor Button Multiscreen Camera Number Buttons Camera Preset Position Number Buttons@2Preset Position Button PRE-POSI Spot Monitor Button SpotLeft Left Right Right @7Auto Button Auto #1Setup/Escape Button SET UP/ESC#2Lock Switch Lock OFF/ON @6Direction Buttons UP/DOWN/LEFT/RIGHT$5Line Selection Switch Line SELECT, 2/4 $1Camera Output Connectors Camera OUT$2Camera Input Connectors Camera $4Line Termination Switch TERM., OFF/ON8Data Port DATA, OUT/IN Installing the WV-PB6164 Data Multiplex Boards InstallationTally Output Setting DIP Switch Setting Alarm Output SettingDummy Black Image Setting Mounting into the Rack Shown below is an example of a basic system connection ConnectionsConnection with the Camera Sites Connections for RS-485 type camera RS-232C Connection with the MonitorsConnection with the PC Data portConnection with External Remote Control Switches Connection with Alarm SensorsSpot and Multiscreen Monitor Monitors and DisplaysConnect the time lapse VCR as shown in the example below Connection with the Time Lapse VCRSetup Procedures Displaying the Setup Menu Setup MenuSetup Menu Programming Setup MenuAlarm Setup Alarm RecallAlarm Schedule Alarm Display on the Monitors Camera Site AlarmVideo Loss Alarm Camera Switching Pulse Loss AlarmDwell Time for Alarm Sequence Alarm Mode on the Multiscreen MonitorAlarm Mode on the Spot Monitor Alarm Recording ModeStill Display Multiscreen Output SetupCamera Title Display Clock DisplayCamera Display Position Setting Sequence ModeSecret View Spot Output Setup Clock Display Record or Multiscreen 2 Output SetupRecord Output Setup Camera Title DisplayRecording Mode Setup Recording Mode Setting DetailsDynamic Recording Multiscreen 2 Output Setup Camera Display Position Sequence ModeSystem Setup Clock SetupClock Display Position Spot Sequence SEQ1 Camera Title SetupSequence Setup Camera Title Display PositionDwell Time Uniform Dwell Time Preset PositionAuto Skip Image AssignmentMulti Sequence SEQ2, SEQ3 Camera/PlaybackDwell Time Programming Steps 2 to Lock ModeSequence Timing Multiscreen Monitor Sequence Timing Spot MonitorCable Compensation/VD2/Data Alarm Terminal SetupCommunication Port Setup Playback ModeData Mode RS-232C ModeDaisy Mode VCR Input SelectUnit Address Password Registration PasswordOther Setup Menus Camera DownloadCamera Upload All Reset Operating Procedures Single Spot Live Controlling the Video Input and MonitorsSelecting the Spot Monitor Single Sequence LiveFreezing Single Spot Live Selecting the Multiscreen MonitorControlling the Camera Images Single Spot LiveZooming Single Spot Live Multiscreen Spot LiveFreezing Multiscreen Spot Live Single or Multi Sequence Live Controlling the Playback ImagesFreezing Single Spot Playback Single Spot PlaybackSingle or Multi Sequence Playback Zooming Single Spot PlaybackMultiscreen Spot Playback Freezing Multiscreen Spot PlaybackMultiscreen Spot Live Images with a Playback Image Displaying the Camera and Playback ImagesFreezing Multiscreen Spot Live Images with a Playback Image Lens Control Controlling Camera Site AccessoriesCamera Control Function Camera SelectionPan/Tilt Control Auto Panning Pan/Tilt Control Preset OperationCamera Setup Pan/Tilt Control Home PositionSimplified preset position setting Alarm Control Function Alarm InputAlarm Operation Spot Output Multiscreen OutputExample of Using Multiscreen 2 Monitor Alarm ResetReset Spot Alarm SuspensionCamera Switching Pulse Loss Display Other FunctionRecording on the Time Lapse VCR Operating Procedures with WV-CU550C Major Operating Controls and Their Functions System Controller WV-CU550C5Preset Position Button PRE-POSI Busy Indicator BusySet Up button SET UP D Time Lapse Mode Buttons T/L MODE, D C@6Mode Selection switch Mode @2Alarm Reset button Reset@4Termination switch TERM., ON/OFF @5Controller Unit Number switch Controller Unit noInstallations Modifying the Front PanelConnection with the WV-CU550C System Controller WJ-FS616C WV-CU550C Function Setup Menu Operations with WV-CU550CControlling the Video Input and Monitors Function Operations with WV-CU550CCamera Control Function RES A.RES Auxiliary Control Alarm Control FunctionSystem Expansion Application Operating ProcedureConnections Other ApplicationsFor Main Site For Local SiteCommunication Protocol Transmission CommandResponse Command AppendixTransmission Response Parameter Ascii Command Ascii Command TableTable below 19 kinds None QOPResponse Command Ascii Main Unit Information Standard Accessories SpecificationsPanasonic Canada Inc