Kenmore I10.8808, I10.8809 manual Ec, ne ,-@se

Page 16

©u ec_, ne _,-@::_se

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

1.Turn cold water faucet off and remove washer inlet hose.

2.Remove old rubber washer from inlet hose and replace with new rubber washer provided. If space permits, attach the brass female end of the "Y" connector to the cold water faucet.

NOTE: If "Y" connector can be attached directly to cold water faucet, go to Step 6. If "Y" connector cannot be attached directly to the cold water faucet, the short hose must be used. Continue with Step 3.

3.Attach short hose to cold water faucet. Screw on coupling by hand until it is seated on faucet.

4.Using pliers, tighten the couplings with an additional two- thirds turn.

9.Attach angled end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector.

10.Using pliers, tighten the coupling with an additional two- thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

NOTE: Do not overtighten. Damage to the coupling can result.

5.Attach "Y" connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector.

6.Attach straight end of long hose to "Y" connector.

7.Attach washer cold inlet hose to other end of "Y" connector. Screw on coupling by hand until it is seated on connector.

8.Using pliers, tighten the couplings with an additional two- thirds turn.

11.Check that the water faucets are on.

12.Check for leaks around "Y" connector, faucet and hoses.

Check the levelness of the dryer. Check levelness first side to side, then front to back.

A

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

A. Inlet to cold water

NOTE: Do not overtighten. Damage to the coupling can result.

16

Image 16

Contents Electric Dryer Table of Contents Kenmore Elite Appliance Warranty ONE Year Limited WarrantyProtection Agreements Master Protection AgreementsDryer Safety Your safety and the safety of others are very important80O-4-MY-HOM E If using a power supply cord Parts suppliedParts needed You will needMobile Home Additional Installation Requirements Installation ClearancesIt is your responsibility Electrical Connection If connecting by direct wireIf your outlet looks like this Direct Wire Ecb caStyle 2 Direct wire strain relief Wire connection Power supply cordWire connection Direct Wire CG F Optional 3-wire connection If using an existing vent system If this is a new vent system Vent materialExhaust Rigid metal ventOptional exhaust installations Special provisions for mobile home installationsVent system chart Determine vent pathNumber Type Box or Angled G0 turns Vent Louvered Hoods Hoods Rigid MetalEc, ne ,-@se Remove the door assembly If the dryer will not start, check the following Dryer USE To use an Auto Dry CycleTo use a Timed Cycle To stop or pause your dryer at any timeDrying tips Cycle tipsAuto Dry Cycles SteamCare Preset Cycle Settings Heavy DutyUltra Delicate Express DRY TMAuto Dry Cycle Modifiers Changing Modifiers and Options after pressing Start Changing the Preset Dryness Level SettingsTo use the dryer rack Dryer Care For direct-wired dryers Troubleshooting Dryer displaying code messageNo heat UnusualsoundsIs the lint screen clogged with lint? Are fabric softener sheets blocking the grille?Is the exhaust vent the correct length? Has the Air Dry modifier been selected?Loads are wrinkled OdorsLint on load Is the lint screen clogged? Is the dryer being used for the first time?Contratos DE Proteccion Garantia Limitada DE UN Aiio Seguridad DE LA SecadoraExclusion DE Garantias Implcitas Limitacion DE Recursos Piezas suministradas Instrucciones DE InstalacionPiezas necesarias Peligro de Explosion Si emplea un cable de suministro elctricoUsted necesitara Usted es responsable de Las instalaciones en casas rodantes necesitanConexibn elctrica Si el contacto de pared luce como steSi el contacto de pared luce come ste Si hace la conexi6n con cableado directoCable de suministro elctrico Cable directo Con Estilo 2 Protector de cables para cable directoConexibn de 4 hilos Cable de suministro elctrico Conexibn de 4 hilos Cable directo CG F Conexibn opcional de 3 hilos Ducto de escape de metal flexible CodosAbrazaderas Ventilaci6nInstalaciones opcionales de escape Peligro de IncendioNo. de Tipo de ducto Capotas de Vueltas Ventilaci6n de De 90 o Caja o tipo Codos PersianaDeterminacibn de la via del ducto de escape Cuadro del sistema de ventilacibnRe& c de C6mo invertir el tope Si la secadora no funciona, revise Io siguiente Peligro de Explosi6n USO DE LA SecadoraSistema de secado de doble acci6n Para hacer cambios durante un ciclo de secado automatico Para usar un ciclo de secado automatico Auto Dry CyclePara usar un Ciclo con vapor SteamOare Cycle Para usar un ciclo programadoPara reanudar la marcha de la secadora Sugerencias de secadoSugerencias de ciclos Mojado WetTowels Ciclos de secado autombticoNormal Ciclos programados Timed Cycles Secado expreso Express DRY TMAjustes prefijados de ciclos programados Modificadores del ciclo de secado autombticoSerial de semi seco Damp Dry Signal Serial de ciclo Cycle SignalSecado al aim Air Dry Tipo de carga TiempoCambio de ciclos despu6s de presionar Inicio Start Cbmo cambiar los ajustes prefijados de nivel de sequedadLimpieza de cada carga Para limpiarImportante Limpieza segun la necesidadPara limpiar el tambor de la secadora En el interior del gabinete de la secadoraEn el ducto de escape Cuidado durante las vacaciones o falta de usoSolucion DE Problemas Sin calorLa secadora muestra mensajes codificados PF corte de corriente, revise Io siguienteIntente Io siguiente Cbdigos de servicio tcnico variables F1, F2, F20, etcPelusa en la ropa El tiempo del ciclo es demasiado cortoRopa arrugada Olores Se esta usando la secadora por primera vez?Your Home W10164636A