Kenmore I10.8808 manual Changing Modifiers and Options after pressing Start, To use the dryer rack

Page 24

OnLoud

OffSoft

Cycle Signal

Cycle Signal Volume

NOTE: When WRINKLE GUARD _ is selected, a tone sounds every 5 minutes until the clothes are removed, or WRINKLE GUARD _ ends.

You can change Auto and Timed Cycles, Modifiers and Options anytime before pressing Start.

•Three short tones sound if an unavailable combination is selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1.Press STOP twice.

2.Select the desired cycle and options.

3.Press START. The dryer starts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected Modifier or Option begins.

1.Press STOP once.

2.Select the new Modifier and/or Options.

3.Press START to continue the cycle.

NOTE: If you happen to press STOP twice, the program clears and your dryer shuts down. Restart the selection process.

Changing the Preset Dryness Level Settings

If all of your loads on all Auto Dry cycles are consistently not as dry as you would like, you may change the preset Dryness Level settings to increase the dryness. This change will affect all of your Auto Dry cycles.

Your Dryness Level settings can be adjusted to adapt to different installations, environmental conditions or personal preference. There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly dryer clothes, approximately 15% more drying time) and 3 (much dryer clothes, approximately 30% more drying time).

1.The Dryness Level settings cannot be changed while the dryer is running.

2.Press and hold the DRYNESS LEVEL button for 5 seconds. The dryer will beep, and "CF" will be displayed for 1 second followed by the current drying setting.

3.To select a new drying setting, press the DRYNESS LEVEL button again until the desired drying setting is shown.

NOTE: While cycling through the settings, the current setting will not flash, but the other settings will flash.

4.Press START to save the drying setting.

5.The drying setting you selected will become your new preset drying setting for all Auto Dry cycles.

The dryer rack was shipped in the dryer drum.

Use the dryer rack for items that you do not want to tumble dry, such as sweaters.

Use Timed Dry to select the desired time.

NOTE: Do not use Auto Dry Cycles with the dryer rack.

To use the dryer rack:

Do not remove the lint screen.

1.Open dryer door.

2.Slide dryer rack over the bottom of the dryer door opening. Rest the back wire on the dryer back ledge. Push down on the frame front to secure over lint screen.

3= Place wet items on top of the dryer rack. Allow space around items for air to circulate. The dryer rack does not move, but the drum will rotate. Make sure items do not hang over the edges or between dryer rack grille.

4.Close the door.

5.Select TIMED DRY and TIME ADJUST MORE TIME or LESS TIME. Refer to the following table.

6.Select the desired temperature setting to match the fabrics in your load by pressing TEMPERATURE. Items containing foam, rubber or plastic must be dried on a clothesline or by using an air cycle. Refer to the following table.

7.Start the dryer.

NOTE: Check the lint screen and remove any lint accumulated from items dried on the dryer rack.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Electric Dryer Table of Contents Kenmore Elite Appliance Warranty ONE Year Limited WarrantyProtection Agreements Master Protection AgreementsDryer Safety Your safety and the safety of others are very important80O-4-MY-HOM E If using a power supply cord Parts suppliedParts needed You will needInstallation Clearances Mobile Home Additional Installation RequirementsIt is your responsibility If connecting by direct wire Electrical ConnectionIf your outlet looks like this Direct Wire Ecb caStyle 2 Direct wire strain relief Wire connection Power supply cordWire connection Direct Wire CG F Optional 3-wire connection If using an existing vent system If this is a new vent system Vent materialExhaust Rigid metal ventOptional exhaust installations Special provisions for mobile home installationsVent system chart Determine vent pathNumber Type Box or Angled G0 turns Vent Louvered Hoods Hoods Rigid MetalEc, ne ,-@se Remove the door assembly If the dryer will not start, check the following Dryer USE To use an Auto Dry CycleTo use a Timed Cycle To stop or pause your dryer at any timeDrying tips Cycle tipsAuto Dry Cycles SteamCare Preset Cycle Settings Heavy DutyUltra Delicate Express DRY TMAuto Dry Cycle Modifiers Changing the Preset Dryness Level Settings Changing Modifiers and Options after pressing StartTo use the dryer rack Dryer Care For direct-wired dryers Troubleshooting Dryer displaying code messageNo heat UnusualsoundsIs the lint screen clogged with lint? Are fabric softener sheets blocking the grille?Is the exhaust vent the correct length? Has the Air Dry modifier been selected?Loads are wrinkled OdorsLint on load Is the lint screen clogged? Is the dryer being used for the first time?Contratos DE Proteccion Seguridad DE LA Secadora Garantia Limitada DE UN AiioExclusion DE Garantias Implcitas Limitacion DE Recursos Instrucciones DE Instalacion Piezas suministradasPiezas necesarias Si emplea un cable de suministro elctrico Peligro de ExplosionUsted necesitara Usted es responsable de Las instalaciones en casas rodantes necesitanConexibn elctrica Si el contacto de pared luce como steSi el contacto de pared luce come ste Si hace la conexi6n con cableado directoCable de suministro elctrico Cable directo Estilo 2 Protector de cables para cable directo ConConexibn de 4 hilos Cable de suministro elctrico Conexibn de 4 hilos Cable directo CG F Conexibn opcional de 3 hilos Ducto de escape de metal flexible CodosAbrazaderas Ventilaci6nInstalaciones opcionales de escape Peligro de IncendioNo. de Tipo de ducto Capotas de Vueltas Ventilaci6n de De 90 o Caja o tipo Codos PersianaDeterminacibn de la via del ducto de escape Cuadro del sistema de ventilacibnRe& c de C6mo invertir el tope Si la secadora no funciona, revise Io siguiente USO DE LA Secadora Peligro de Explosi6nSistema de secado de doble acci6n Para hacer cambios durante un ciclo de secado automatico Para usar un ciclo de secado automatico Auto Dry CyclePara usar un Ciclo con vapor SteamOare Cycle Para usar un ciclo programadoPara reanudar la marcha de la secadora Sugerencias de secadoSugerencias de ciclos Mojado WetCiclos de secado autombtico TowelsNormal Ciclos programados Timed Cycles Secado expreso Express DRY TMAjustes prefijados de ciclos programados Modificadores del ciclo de secado autombticoSerial de semi seco Damp Dry Signal Serial de ciclo Cycle SignalSecado al aim Air Dry Tipo de carga TiempoCambio de ciclos despu6s de presionar Inicio Start Cbmo cambiar los ajustes prefijados de nivel de sequedadLimpieza de cada carga Para limpiarImportante Limpieza segun la necesidadPara limpiar el tambor de la secadora En el interior del gabinete de la secadoraEn el ducto de escape Cuidado durante las vacaciones o falta de usoSolucion DE Problemas Sin calorLa secadora muestra mensajes codificados PF corte de corriente, revise Io siguienteIntente Io siguiente Cbdigos de servicio tcnico variables F1, F2, F20, etcEl tiempo del ciclo es demasiado corto Pelusa en la ropaRopa arrugada Olores Se esta usando la secadora por primera vez?Your Home W10164636A
Top Page Image Contents