Kenmore I10.8809, I10.8808 manual Remove the door assembly

Page 17

You can change your door swing from a right-side opening to a left-side opening, if desired.

1.Place a towel or soft cloth on top of the dryer or work space to protect the surface.

Remove the door assembly

1.Open the dryer door.

2.Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front panel of the dryer.

3.Loosen the top screw from each of the 2 hinges in Step 2.

-A

.A

"B

A. Loosen these screws.

B. Remove these screws.

4.Remove the dryer door and the hinges by lifting upward on the door. Lay the door on a flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose screws from dryer front panel.

5.Remove the 4 plastic plugs located outside the dryer door opening.

6.Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in Step 4.

Reverse the strike

1.Remove the door strike from the dryer door opening.

2.Remove the cosmetic screw opposite the door strike.

A. Door strike

B. Cosmetic screw

3.Reinstall the door strike and cosmetic screw on the opposite side of the dryer door opening from where they were removed.

NOTE: Door strike and plugs must be on the same side of the dryer door opening.

Reinstall the door

1.Remove the 4 screws and 2 hinges from the dryer door.

2.Replace the 4 screws in the same holes.

J

3.Remove the 4 screws from the opposite side of the door.

I

17

Image 17

Contents Electric Dryer Table of Contents ONE Year Limited Warranty Kenmore Elite Appliance WarrantyProtection Agreements Master Protection AgreementsYour safety and the safety of others are very important Dryer SafetyParts supplied 80O-4-MY-HOM E If using a power supply cordParts needed You will needIt is your responsibility Installation ClearancesMobile Home Additional Installation Requirements If your outlet looks like this If connecting by direct wireElectrical Connection Ecb ca Direct WireWire connection Power supply cord Style 2 Direct wire strain reliefWire connection Direct Wire CG F Optional 3-wire connection If this is a new vent system Vent material If using an existing vent systemExhaust Rigid metal ventSpecial provisions for mobile home installations Optional exhaust installationsDetermine vent path Vent system chartNumber Type Box or Angled G0 turns Vent Louvered Hoods Hoods Rigid MetalEc, ne ,-@se Remove the door assembly If the dryer will not start, check the following To use an Auto Dry Cycle Dryer USETo stop or pause your dryer at any time To use a Timed CycleDrying tips Cycle tipsAuto Dry Cycles Heavy Duty SteamCare Preset Cycle SettingsUltra Delicate Express DRY TMAuto Dry Cycle Modifiers To use the dryer rack Changing the Preset Dryness Level SettingsChanging Modifiers and Options after pressing Start Dryer Care For direct-wired dryers Dryer displaying code message TroubleshootingNo heat UnusualsoundsAre fabric softener sheets blocking the grille? Is the lint screen clogged with lint?Is the exhaust vent the correct length? Has the Air Dry modifier been selected?Odors Loads are wrinkledLint on load Is the lint screen clogged? Is the dryer being used for the first time?Contratos DE Proteccion Exclusion DE Garantias Implcitas Limitacion DE Recursos Seguridad DE LA SecadoraGarantia Limitada DE UN Aiio Piezas necesarias Instrucciones DE InstalacionPiezas suministradas Usted necesitara Si emplea un cable de suministro elctricoPeligro de Explosion Las instalaciones en casas rodantes necesitan Usted es responsable deConexibn elctrica Si el contacto de pared luce como steSi hace la conexi6n con cableado directo Si el contacto de pared luce come steCable de suministro elctrico Cable directo Conexibn de 4 hilos Cable de suministro elctrico Estilo 2 Protector de cables para cable directoCon Conexibn de 4 hilos Cable directo CG F Conexibn opcional de 3 hilos Codos Ducto de escape de metal flexibleAbrazaderas Ventilaci6nPeligro de Incendio Instalaciones opcionales de escapeDe 90 o Caja o tipo Codos Persiana No. de Tipo de ducto Capotas de Vueltas Ventilaci6n deDeterminacibn de la via del ducto de escape Cuadro del sistema de ventilacibnRe& c de C6mo invertir el tope Si la secadora no funciona, revise Io siguiente Sistema de secado de doble acci6n USO DE LA SecadoraPeligro de Explosi6n Para usar un ciclo de secado automatico Auto Dry Cycle Para hacer cambios durante un ciclo de secado automaticoPara usar un Ciclo con vapor SteamOare Cycle Para usar un ciclo programadoSugerencias de secado Para reanudar la marcha de la secadoraSugerencias de ciclos Mojado WetNormal Ciclos de secado autombticoTowels Secado expreso Express DRY TM Ciclos programados Timed CyclesAjustes prefijados de ciclos programados Modificadores del ciclo de secado autombticoSerial de ciclo Cycle Signal Serial de semi seco Damp Dry SignalSecado al aim Air Dry Tipo de carga TiempoCbmo cambiar los ajustes prefijados de nivel de sequedad Cambio de ciclos despu6s de presionar Inicio StartPara limpiar Limpieza de cada cargaImportante Limpieza segun la necesidadEn el interior del gabinete de la secadora Para limpiar el tambor de la secadoraEn el ducto de escape Cuidado durante las vacaciones o falta de usoSin calor Solucion DE ProblemasPF corte de corriente, revise Io siguiente La secadora muestra mensajes codificadosIntente Io siguiente Cbdigos de servicio tcnico variables F1, F2, F20, etcRopa arrugada El tiempo del ciclo es demasiado cortoPelusa en la ropa Se esta usando la secadora por primera vez? OloresW10164636A Your Home