Kenmore I10.8808 Is the lint screen clogged with lint?, Is the exhaust vent the correct length?

Page 28

Clothes are not drying satisfactorily, drying times are too long, or load is too hot

•Is the lint screen clogged with lint?

Lint screen should be cleaned before each load.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to fellow these instructions can result in death or fire.

Is the exhaust vent or outside exhaust hood clogged with lint, restricting air movement?

Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent. See "Installation Instructions."

Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many turns. Long venting will increase drying times. See "Installation Instructions."

Is the exhaust vent diameter the correct size? Use 4" (10.2 cm) diameter vent material.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

Is the dryer located in a room with temperature below 45°F (7°C)?

Proper operation of dryer cycles requires temperatures above 45°F (7°C).

Is the dryer located in a closet?

Closet doors must have ventilation openings at the top and bottom of the door. The rear of the dryer requires 5" (12.7 cm) of airspace. See "Installation Instructions."

Has the Air Dry modifier been selected?

Select the right temperature for the types of garments being dried. See "Modifiers."

Is the load too large and heavy to dry quickly? Separate the load to tumble freely.

Are all your Auto Dry cycle loads consistently not as dry as you would like?

You may change the preset Dryness Level settings to increase dryness for all Auto Dry cycles. See "Changing Cycles, Modifiers and Options."

Are clothes coming out of the Refresh cycle with damp or wet spots?

Under certain environmental or installation conditions you may experience underdrying. Select the Touch Up cycle

(20 min. default time), which can be customized by choosing temperature by pressing TEMP and/or cycle time by pressing the Timed Cycle Adjust up or down buttons.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Electric Dryer Table of Contents Kenmore Elite Appliance Warranty ONE Year Limited WarrantyProtection Agreements Master Protection AgreementsDryer Safety Your safety and the safety of others are very important80O-4-MY-HOM E If using a power supply cord Parts suppliedParts needed You will needMobile Home Additional Installation Requirements Installation ClearancesIt is your responsibility Electrical Connection If connecting by direct wireIf your outlet looks like this Direct Wire Ecb caStyle 2 Direct wire strain relief Wire connection Power supply cordWire connection Direct Wire CG F Optional 3-wire connection If using an existing vent system If this is a new vent system Vent materialExhaust Rigid metal ventOptional exhaust installations Special provisions for mobile home installationsVent system chart Determine vent pathNumber Type Box or Angled G0 turns Vent Louvered Hoods Hoods Rigid MetalEc, ne ,-@se Remove the door assembly If the dryer will not start, check the following Dryer USE To use an Auto Dry CycleTo use a Timed Cycle To stop or pause your dryer at any timeDrying tips Cycle tipsAuto Dry Cycles SteamCare Preset Cycle Settings Heavy DutyUltra Delicate Express DRY TMAuto Dry Cycle Modifiers Changing Modifiers and Options after pressing Start Changing the Preset Dryness Level SettingsTo use the dryer rack Dryer Care For direct-wired dryers Troubleshooting Dryer displaying code messageNo heat UnusualsoundsIs the lint screen clogged with lint? Are fabric softener sheets blocking the grille?Is the exhaust vent the correct length? Has the Air Dry modifier been selected?Loads are wrinkled OdorsLint on load Is the lint screen clogged? Is the dryer being used for the first time?Contratos DE Proteccion Garantia Limitada DE UN Aiio Seguridad DE LA SecadoraExclusion DE Garantias Implcitas Limitacion DE Recursos Piezas suministradas Instrucciones DE InstalacionPiezas necesarias Peligro de Explosion Si emplea un cable de suministro elctricoUsted necesitara Usted es responsable de Las instalaciones en casas rodantes necesitanConexibn elctrica Si el contacto de pared luce como steSi el contacto de pared luce come ste Si hace la conexi6n con cableado directoCable de suministro elctrico Cable directo Con Estilo 2 Protector de cables para cable directoConexibn de 4 hilos Cable de suministro elctrico Conexibn de 4 hilos Cable directo CG F Conexibn opcional de 3 hilos Ducto de escape de metal flexible CodosAbrazaderas Ventilaci6nInstalaciones opcionales de escape Peligro de IncendioNo. de Tipo de ducto Capotas de Vueltas Ventilaci6n de De 90 o Caja o tipo Codos PersianaDeterminacibn de la via del ducto de escape Cuadro del sistema de ventilacibnRe& c de C6mo invertir el tope Si la secadora no funciona, revise Io siguiente Peligro de Explosi6n USO DE LA SecadoraSistema de secado de doble acci6n Para hacer cambios durante un ciclo de secado automatico Para usar un ciclo de secado automatico Auto Dry CyclePara usar un Ciclo con vapor SteamOare Cycle Para usar un ciclo programadoPara reanudar la marcha de la secadora Sugerencias de secadoSugerencias de ciclos Mojado WetTowels Ciclos de secado autombticoNormal Ciclos programados Timed Cycles Secado expreso Express DRY TMAjustes prefijados de ciclos programados Modificadores del ciclo de secado autombticoSerial de semi seco Damp Dry Signal Serial de ciclo Cycle SignalSecado al aim Air Dry Tipo de carga TiempoCambio de ciclos despu6s de presionar Inicio Start Cbmo cambiar los ajustes prefijados de nivel de sequedadLimpieza de cada carga Para limpiarImportante Limpieza segun la necesidadPara limpiar el tambor de la secadora En el interior del gabinete de la secadoraEn el ducto de escape Cuidado durante las vacaciones o falta de usoSolucion DE Problemas Sin calorLa secadora muestra mensajes codificados PF corte de corriente, revise Io siguienteIntente Io siguiente Cbdigos de servicio tcnico variables F1, F2, F20, etcPelusa en la ropa El tiempo del ciclo es demasiado cortoRopa arrugada Olores Se esta usando la secadora por primera vez?Your Home W10164636A
Top Page Image Contents