Kenmore I10.8808, I10.8809 manual Wire connection Direct Wire

Page 10

2= Remove neutral ground wire from external ground conductor

screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.

B

5.Tighten strain relief screws.

6.Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

7.You have completed your electrical connection. Now go to "Venting Requirements."

4-wire connection: Direct Wire

A ....................... i

A. Neutral ground wire

B. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to center silver-coloredterminal block screw.

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. 3_,, (1.9 cm) UL listed strain relief

3= Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.

A. External ground conductor screw

B. Neutral ground wire

C. Ground wire (green or bare) of power supply cord

D. 3_,, (1.9 cm) UL ilsted strain relief

E. Center silver-colored terminal block screw

E Neutral wire (white or center wire)

4.Connect the other wires to outer terminal block screws. Tighten screws.

!!!!

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3 wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5" (12.7 cm). Cut 11/2''(3.8 cm) from

3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of wires into a hook shape.

1"

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

1= Remove center silver-colored terminal block screw.

2.Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block. Squeeze hooked ends together. Tighten screw.

A. Neutral ground wire

B. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw.

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. 3/4" (1.9 cm) UL Iisted strain relief

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Electric Dryer Table of Contents Protection Agreements Kenmore Elite Appliance WarrantyONE Year Limited Warranty Master Protection AgreementsDryer Safety Your safety and the safety of others are very importantParts needed 80O-4-MY-HOM E If using a power supply cordParts supplied You will needMobile Home Additional Installation Requirements Installation ClearancesIt is your responsibility Electrical Connection If connecting by direct wireIf your outlet looks like this Direct Wire Ecb caStyle 2 Direct wire strain relief Wire connection Power supply cordWire connection Direct Wire CG F Optional 3-wire connection Exhaust If using an existing vent systemIf this is a new vent system Vent material Rigid metal ventOptional exhaust installations Special provisions for mobile home installationsNumber Type Box or Angled G0 turns Vent Louvered Hoods Vent system chartDetermine vent path Hoods Rigid MetalEc, ne ,-@se Remove the door assembly If the dryer will not start, check the following Dryer USE To use an Auto Dry CycleDrying tips To use a Timed CycleTo stop or pause your dryer at any time Cycle tipsAuto Dry Cycles Ultra Delicate SteamCare Preset Cycle SettingsHeavy Duty Express DRY TMAuto Dry Cycle Modifiers Changing Modifiers and Options after pressing Start Changing the Preset Dryness Level SettingsTo use the dryer rack Dryer Care For direct-wired dryers No heat TroubleshootingDryer displaying code message UnusualsoundsIs the exhaust vent the correct length? Is the lint screen clogged with lint?Are fabric softener sheets blocking the grille? Has the Air Dry modifier been selected?Lint on load Is the lint screen clogged? Loads are wrinkledOdors Is the dryer being used for the first time?Contratos DE Proteccion Garantia Limitada DE UN Aiio Seguridad DE LA SecadoraExclusion DE Garantias Implcitas Limitacion DE Recursos Piezas suministradas Instrucciones DE InstalacionPiezas necesarias Peligro de Explosion Si emplea un cable de suministro elctricoUsted necesitara Conexibn elctrica Usted es responsable deLas instalaciones en casas rodantes necesitan Si el contacto de pared luce como steSi el contacto de pared luce come ste Si hace la conexi6n con cableado directoCable de suministro elctrico Cable directo Con Estilo 2 Protector de cables para cable directoConexibn de 4 hilos Cable de suministro elctrico Conexibn de 4 hilos Cable directo CG F Conexibn opcional de 3 hilos Abrazaderas Ducto de escape de metal flexibleCodos Ventilaci6nInstalaciones opcionales de escape Peligro de IncendioDeterminacibn de la via del ducto de escape No. de Tipo de ducto Capotas de Vueltas Ventilaci6n deDe 90 o Caja o tipo Codos Persiana Cuadro del sistema de ventilacibnRe& c de C6mo invertir el tope Si la secadora no funciona, revise Io siguiente Peligro de Explosi6n USO DE LA SecadoraSistema de secado de doble acci6n Para usar un Ciclo con vapor SteamOare Cycle Para hacer cambios durante un ciclo de secado automaticoPara usar un ciclo de secado automatico Auto Dry Cycle Para usar un ciclo programadoSugerencias de ciclos Para reanudar la marcha de la secadoraSugerencias de secado Mojado WetTowels Ciclos de secado autombticoNormal Ajustes prefijados de ciclos programados Ciclos programados Timed CyclesSecado expreso Express DRY TM Modificadores del ciclo de secado autombticoSecado al aim Air Dry Serial de semi seco Damp Dry SignalSerial de ciclo Cycle Signal Tipo de carga TiempoCambio de ciclos despu6s de presionar Inicio Start Cbmo cambiar los ajustes prefijados de nivel de sequedadImportante Limpieza de cada cargaPara limpiar Limpieza segun la necesidadEn el ducto de escape Para limpiar el tambor de la secadoraEn el interior del gabinete de la secadora Cuidado durante las vacaciones o falta de usoSolucion DE Problemas Sin calorIntente Io siguiente La secadora muestra mensajes codificadosPF corte de corriente, revise Io siguiente Cbdigos de servicio tcnico variables F1, F2, F20, etcPelusa en la ropa El tiempo del ciclo es demasiado cortoRopa arrugada Olores Se esta usando la secadora por primera vez?Your Home W10164636A
Top Page Image Contents