Kenmore I10.8808, I10.8809 manual If the dryer will not start, check the following

Page 18

4.Install the 2 hinges to the front panel of the dryer using

4 screws. Use the non-slotted side to attach the hinge to the front panel.

5.Install screws in the top hinge holes in the door. Do not tighten screws. Leave approximately 1A" (5 mm) of screw exposed.

A. Install these screws first.

6.Hang door by placing screw heads into top slotted holes of hinges and slide door down. Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge screws.

7.Close door to engage door strike.

1.Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2.Check that you have all of your tools.

3.Dispose of/recycle all packaging materials,

4.Be sure the water faucets are on.

5.Check for leaks around "Y" connector, faucet and hoses.

6.Check the dryer's final location. Be sure the vent is not crushed or kinked.

7.Check that the dryer is level. See "Level Dryer."

8.For power supply cord installation, plug into an outlet. For direct wire installation, turn on power.

9.Remove any protective film or tape remaining on the dryer.

NOTE: Glass door models have a protective film on the window that should be removed.

10.Read "Dryer Use."

11.Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

12.If you live in a hard water area, use of a water softener is recommended to control the buildup of scale through the water system in the dryer. Over time, the buildup of lime scale may clog different parts of the water system, which will reduce product performance. Excessive scale buildup may lead to the need for certain part replacement or repair.

13.Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this test, do not select the Air Only modifier.

If the dryer will not start, check the following:

•Controls are set in a running or "On" position.

•Start button has been pushed firmly.

•Dryer is plugged into an outlet and/or electrical supply is on.

•Household fuse is intact and tight, or circuit breaker has not tripped.

•Dryer door is closed.

This dryer automatically runs an installation diagnostic routine at the start of its first cycle.

If you receive an "L2" code, there may be a problem with your home power supply keeping the dryer's heater from turning

on. See "Troubleshooting."

If you receive an "AF" code, your dryer vent may be crushed or blocked. See "Troubleshooting."

NOTE: You may notice a burning odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Electric Dryer Table of Contents Protection Agreements Kenmore Elite Appliance WarrantyONE Year Limited Warranty Master Protection AgreementsDryer Safety Your safety and the safety of others are very importantParts needed 80O-4-MY-HOM E If using a power supply cordParts supplied You will needInstallation Clearances Mobile Home Additional Installation RequirementsIt is your responsibility If connecting by direct wire Electrical ConnectionIf your outlet looks like this Direct Wire Ecb caStyle 2 Direct wire strain relief Wire connection Power supply cordWire connection Direct Wire CG F Optional 3-wire connection Exhaust If using an existing vent systemIf this is a new vent system Vent material Rigid metal ventOptional exhaust installations Special provisions for mobile home installationsNumber Type Box or Angled G0 turns Vent Louvered Hoods Vent system chartDetermine vent path Hoods Rigid MetalEc, ne ,-@se Remove the door assembly If the dryer will not start, check the following Dryer USE To use an Auto Dry CycleDrying tips To use a Timed CycleTo stop or pause your dryer at any time Cycle tipsAuto Dry Cycles Ultra Delicate SteamCare Preset Cycle SettingsHeavy Duty Express DRY TMAuto Dry Cycle Modifiers Changing the Preset Dryness Level Settings Changing Modifiers and Options after pressing StartTo use the dryer rack Dryer Care For direct-wired dryers No heat TroubleshootingDryer displaying code message UnusualsoundsIs the exhaust vent the correct length? Is the lint screen clogged with lint?Are fabric softener sheets blocking the grille? Has the Air Dry modifier been selected?Lint on load Is the lint screen clogged? Loads are wrinkledOdors Is the dryer being used for the first time?Contratos DE Proteccion Seguridad DE LA Secadora Garantia Limitada DE UN AiioExclusion DE Garantias Implcitas Limitacion DE Recursos Instrucciones DE Instalacion Piezas suministradasPiezas necesarias Si emplea un cable de suministro elctrico Peligro de ExplosionUsted necesitara Conexibn elctrica Usted es responsable deLas instalaciones en casas rodantes necesitan Si el contacto de pared luce como steSi el contacto de pared luce come ste Si hace la conexi6n con cableado directoCable de suministro elctrico Cable directo Estilo 2 Protector de cables para cable directo ConConexibn de 4 hilos Cable de suministro elctrico Conexibn de 4 hilos Cable directo CG F Conexibn opcional de 3 hilos Abrazaderas Ducto de escape de metal flexibleCodos Ventilaci6nInstalaciones opcionales de escape Peligro de IncendioDeterminacibn de la via del ducto de escape No. de Tipo de ducto Capotas de Vueltas Ventilaci6n deDe 90 o Caja o tipo Codos Persiana Cuadro del sistema de ventilacibnRe& c de C6mo invertir el tope Si la secadora no funciona, revise Io siguiente USO DE LA Secadora Peligro de Explosi6nSistema de secado de doble acci6n Para usar un Ciclo con vapor SteamOare Cycle Para hacer cambios durante un ciclo de secado automaticoPara usar un ciclo de secado automatico Auto Dry Cycle Para usar un ciclo programadoSugerencias de ciclos Para reanudar la marcha de la secadoraSugerencias de secado Mojado WetCiclos de secado autombtico TowelsNormal Ajustes prefijados de ciclos programados Ciclos programados Timed CyclesSecado expreso Express DRY TM Modificadores del ciclo de secado autombticoSecado al aim Air Dry Serial de semi seco Damp Dry SignalSerial de ciclo Cycle Signal Tipo de carga TiempoCambio de ciclos despu6s de presionar Inicio Start Cbmo cambiar los ajustes prefijados de nivel de sequedadImportante Limpieza de cada cargaPara limpiar Limpieza segun la necesidadEn el ducto de escape Para limpiar el tambor de la secadoraEn el interior del gabinete de la secadora Cuidado durante las vacaciones o falta de usoSolucion DE Problemas Sin calorIntente Io siguiente La secadora muestra mensajes codificadosPF corte de corriente, revise Io siguiente Cbdigos de servicio tcnico variables F1, F2, F20, etcEl tiempo del ciclo es demasiado corto Pelusa en la ropaRopa arrugada Olores Se esta usando la secadora por primera vez?Your Home W10164636A
Top Page Image Contents