Kenmore I10.8809, I10.8808 Loads are wrinkled, Odors, Lint on load Is the lint screen clogged?

Page 29

Cycle time too short

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

•Is the Auto Dry Cycle ending early?

The load may not be contacting the sensor strips. Level the dryer.

Change the dryness level setting on Auto Dry Cycles. Increasing or decreasing the dryness level will change the amount of drying time in a cycle.

Do not use a dryer rack with an Auto Dry Cycle.

Lint on load

•Is the lint screen clogged?

Clean lint screen. Check for air movement.

Stains on load or drum

•Was dryer fabric softener properly used?

Add dryer fabric softener sheets at the beginning of the cycle. Fabric softener sheets added to a partially dried load can stain your garments.

Drum stains are caused by dyes in clothing (usually blue jeans). This will not transfer to other clothing.

Loads are wrinkled

•Was the load removed from dryer at the end of the cycle? Select Touch Up Cycle to tumble the load with water and heat to help smooth out wrinkles from a load left in the dryer.

Was the dryer overloaded?

Dry smaller loads that can tumble freely. Smaller loads yield best results with the Refresh Cycle. Results may also vary depending on fabric type. This cycle is best for reducing wrinkles and odors from loads consisting of wrinkle-free cotton, cotton polyester blends, common knits and synthetics.

Loads are still wrinkled following SteamCare cycles? Make sure water is connected to the dryer. Check that water inlet hose is connected to both the faucet and dryer'swater inlet valve. Check that the water supply is turned on. These cycles are best for smoothing out wrinkles and reducing odors from loads consisting of wrinkle-free cotton, cotton polyester blends, common knits and synthetic garments.

NOTE: Refer to garment care label instructions, Dry clean only garments are not recommended.

Odors

Have you recently been painting, staining or varnishing in the area where your dryer is located?

If so, ventilate the area. When the odors or fumes are gone from the area, rewash and dry the clothing.

•Is the dryer being used for the first time?

The new electric heating element may have an odor. The odor will be gone after the first cycle.

Is water connected to the dryer?

Check that water inlet hose is connected to both the faucet

and dryer's water inlet valve. Check that the water supply is turned on.

To remove odors left in garments after wearing, select the Refresh cycle for small loads of two to four garments. This cycle is best for reducing wrinkles and odors from loads consisting of wrinkle-free cotton, cotton polyester blends, common knits and synthetics.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Electric Dryer Table of Contents ONE Year Limited Warranty Kenmore Elite Appliance WarrantyProtection Agreements Master Protection AgreementsYour safety and the safety of others are very important Dryer SafetyParts supplied 80O-4-MY-HOM E If using a power supply cordParts needed You will needIt is your responsibility Installation ClearancesMobile Home Additional Installation Requirements If your outlet looks like this If connecting by direct wireElectrical Connection Ecb ca Direct WireWire connection Power supply cord Style 2 Direct wire strain reliefWire connection Direct Wire CG F Optional 3-wire connection If this is a new vent system Vent material If using an existing vent systemExhaust Rigid metal ventSpecial provisions for mobile home installations Optional exhaust installationsDetermine vent path Vent system chartNumber Type Box or Angled G0 turns Vent Louvered Hoods Hoods Rigid MetalEc, ne ,-@se Remove the door assembly If the dryer will not start, check the following To use an Auto Dry Cycle Dryer USETo stop or pause your dryer at any time To use a Timed CycleDrying tips Cycle tipsAuto Dry Cycles Heavy Duty SteamCare Preset Cycle SettingsUltra Delicate Express DRY TMAuto Dry Cycle Modifiers To use the dryer rack Changing the Preset Dryness Level SettingsChanging Modifiers and Options after pressing Start Dryer Care For direct-wired dryers Dryer displaying code message TroubleshootingNo heat UnusualsoundsAre fabric softener sheets blocking the grille? Is the lint screen clogged with lint?Is the exhaust vent the correct length? Has the Air Dry modifier been selected?Odors Loads are wrinkledLint on load Is the lint screen clogged? Is the dryer being used for the first time?Contratos DE Proteccion Exclusion DE Garantias Implcitas Limitacion DE Recursos Seguridad DE LA SecadoraGarantia Limitada DE UN Aiio Piezas necesarias Instrucciones DE InstalacionPiezas suministradas Usted necesitara Si emplea un cable de suministro elctricoPeligro de Explosion Las instalaciones en casas rodantes necesitan Usted es responsable deConexibn elctrica Si el contacto de pared luce como steSi hace la conexi6n con cableado directo Si el contacto de pared luce come steCable de suministro elctrico Cable directo Conexibn de 4 hilos Cable de suministro elctrico Estilo 2 Protector de cables para cable directoCon Conexibn de 4 hilos Cable directo CG F Conexibn opcional de 3 hilos Codos Ducto de escape de metal flexibleAbrazaderas Ventilaci6nPeligro de Incendio Instalaciones opcionales de escapeDe 90 o Caja o tipo Codos Persiana No. de Tipo de ducto Capotas de Vueltas Ventilaci6n deDeterminacibn de la via del ducto de escape Cuadro del sistema de ventilacibnRe& c de C6mo invertir el tope Si la secadora no funciona, revise Io siguiente Sistema de secado de doble acci6n USO DE LA SecadoraPeligro de Explosi6n Para usar un ciclo de secado automatico Auto Dry Cycle Para hacer cambios durante un ciclo de secado automaticoPara usar un Ciclo con vapor SteamOare Cycle Para usar un ciclo programadoSugerencias de secado Para reanudar la marcha de la secadoraSugerencias de ciclos Mojado WetNormal Ciclos de secado autombticoTowels Secado expreso Express DRY TM Ciclos programados Timed CyclesAjustes prefijados de ciclos programados Modificadores del ciclo de secado autombticoSerial de ciclo Cycle Signal Serial de semi seco Damp Dry SignalSecado al aim Air Dry Tipo de carga TiempoCbmo cambiar los ajustes prefijados de nivel de sequedad Cambio de ciclos despu6s de presionar Inicio StartPara limpiar Limpieza de cada cargaImportante Limpieza segun la necesidadEn el interior del gabinete de la secadora Para limpiar el tambor de la secadoraEn el ducto de escape Cuidado durante las vacaciones o falta de usoSin calor Solucion DE ProblemasPF corte de corriente, revise Io siguiente La secadora muestra mensajes codificadosIntente Io siguiente Cbdigos de servicio tcnico variables F1, F2, F20, etcRopa arrugada El tiempo del ciclo es demasiado cortoPelusa en la ropa Se esta usando la secadora por primera vez? OloresW10164636A Your Home
Top Page Image Contents