GSI Outdoors PNEG-951 manual Load Delay

Page 37

Load Delay

The load delay is used to delay the starting of the load auger when the dryer is unloading to prevent the load auger from cycling to often. To change the setting of this delay follow these instructions:

1. Press the

button.

2. Press the

button.

3.	Press the	button to adjust the settings.
4.	Press the	button to accept the changes.

Out of Grain Timer

The Out of Grain timer should be set to the maximum time it takes for your dryer to refill during continious or batch mode drying.

If the dryer runs out of grain while the load auger switch is in the auto position, the out of grain timer auto- matically shuts off the dryer after the period of time preset on the timer.

1. Press the

button. Press

to bypass the first screen.

2. Press the

button.

PNEG-951

37

Image 37

Contents 3 Module Network Portable Dryer Models Page Table of Contents Drying Charts Module Network Dryer Manual Introduction Section GSI GROUP, INC. Warranty Safety First Dryer Operation Decal DC-889 Decal DC-972 Decal DC-1227 Decal DC-973 USE Caution in the Operation of this Equipment PNEG-951 Control Panel Switch Panel Layout Drying Mode Switch Control Power SwitchLoad Auger Switch FAN SwitchOutside Light Switch Moisture Control SwitchRUN Switch Stop SwitchSetup Button Screens Button Delay ButtonOut of Grain Time Set Out of Grain Meter Roll SP Avg View Grain TempsUser Hour Meter DRY Button Help ButtonCool Button Unload ButtonStats Button PNEG-951 Dryer Pre Season Checks Inspect the Metering Rolls Electrical PowerRUN Button Fuel CheckUnload ONE Speed Operation Load AugerUnload TWO Speed Operation Metering Roll OperationBurner Safety FAN SwitchesBurner Test Fire Meter Roll 2 Speed DisplayEmergency Dryer Shutdown Dryer ShutdownPNEG-951 Dryer Startup and Operation Timer and Delay Settings Initial Setup ParametersFan and Auger Delays Dryer ShutdownLoad Delay OUT of Grain TMR position Unload Delay Drying mode switch is in the Continuous position Setting Up The Temperature Set PointsStartup Startup ProcedureFull Heat-Continuous Flow Operation Continuous Flow Drying ModeDry and Cool-Continuous Flow Operation Continuous-Batch Operation Staged Batch Drying ModePNEG-951 Dry Timer Main Display Screen Operating Display ScreensPNEG-951 Safety Circuit Shutdown Messages Air Switch x Stuck FAN and Heater Generated ErrorsFan x Loss of Airflow Fan x No AirflowGrain Temp Short Housing x High LimitGrain x Overheat Ignition FailureMotor Overload Illegal FlamePlenum Temp Open Plenum Temp ShortVapor x High Limit INPUT/OUTPUT Generated ErrorsAir System Failure Aux Load OverloadLoad Motor Overload Grain Discharge WarningMeter Rolls Failed Out of GrainUser Safety Master Display Generated ErrorsCont-Batch Mode Chng Unload Motor OverloadNetwork Failed Mast Network Failed I/OService and Maintanance Lubrication Procedure Seasonal Inspection and ServiceFAN Blade Removal and Installation FAN Removaland Installation FAN Motor Removal Heater Parts Removal and InstallationMain Controls Meter Roll ServicingHOW to Clear a Jammed Metering Roll Trouble Analysis Procedure PNEG-951 PNEG-951 PNEG-951 PNEG-951 Special Setup Screens AIR Switch Testing Meter Roll DisableMeter Roll Reverse Select Unload Method Reverse timeAttempt to Refill Select Dryer AddressModel Number FAN/HEATER Select Temperature ScaleSET Time & Date Possible reasons for using On/Off burnerContrast Adjustment PNEG-951 Drying Charts Series Dryers Continuous Dry & Cool Staged Batch Continuous Full Heat Continuous Dry & Cool Staged Batch PNEG-951 Technical Reference Control Panel Jumper Wiring Control Panel Internal Wiring PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 Lower Control BOX Back Panelwiring Network FAN/HEATER Interface FAN Computer Pinouts FAN Control BOX Upper Terminal Strip Upper Back Panel Control Wiring 100 PNEG-951 PNEG-951 101 GSI Group, Inc 1004 E. Illinois St Assumption, IL Phone Fax