GSI Outdoors PNEG-951 manual Setting Up The Temperature Set Points

Page 40

Setting Up The Temperature Set Points

These set points are monitored by the computer to control certain features of the dryer. These can be adjusted

from the keypad of the Dryer control panel using the

button or the

button.

Moisture Control Setpoint

Drying mode switch is in the Continuous position:

If the moisture control temperature is below this set point and you have your unload switch set to two speed position then meter rolls will discharge the grain using the low speed meter roll setting.

If the moisture control temperature is above this set point and you have your unload switch set to two speed position then meter rolls will discharge the grain using the high speed meter roll setting.

It is normal for the meter rolls to switch back and forth between high and low speed during the drying pro- cess. This regulates the speed of the grain being discharged from the dryer.

Drying mode switch is in the Batch position:

If the moisture control temperature is below this set point and the Dry Timer has reached zero, the heater will continue to fire until the moisture control set point has been reached. During this cycle the moisture control light will flash and a message on the display will read TEMPERATURE HOLD.

To change the setting of the moisture control temperature follow these instructions:

1. Press the

temp button.

2. Press the

button.

3.	Press the	button to adjust the settings.
4.	Press the	button to accept the changes.

40

PNEG-951

Image 40

Contents 3 Module Network Portable Dryer Models Page Table of Contents Drying Charts Module Network Dryer Manual Introduction Section GSI GROUP, INC. Warranty Safety First Dryer Operation Decal DC-889 Decal DC-972 Decal DC-1227 Decal DC-973 USE Caution in the Operation of this Equipment PNEG-951 Control Panel Switch Panel Layout Control Power Switch Drying Mode SwitchLoad Auger Switch FAN SwitchMoisture Control Switch Outside Light SwitchRUN Switch Stop SwitchSetup Button Screens Button Delay ButtonOut of Grain Time Set Out of Grain View Grain Temps Meter Roll SP AvgUser Hour Meter Help Button DRY ButtonCool Button Unload ButtonStats Button PNEG-951 Dryer Pre Season Checks Electrical Power Inspect the Metering RollsRUN Button Fuel CheckLoad Auger Unload ONE Speed OperationUnload TWO Speed Operation Metering Roll OperationFAN Switches Burner SafetyBurner Test Fire Meter Roll 2 Speed DisplayDryer Shutdown Emergency Dryer ShutdownPNEG-951 Dryer Startup and Operation Initial Setup Parameters Timer and Delay SettingsFan and Auger Delays Dryer ShutdownLoad Delay OUT of Grain TMR position Unload Delay Setting Up The Temperature Set Points Drying mode switch is in the Continuous positionStartup Procedure StartupContinuous Flow Drying Mode Full Heat-Continuous Flow OperationDry and Cool-Continuous Flow Operation Staged Batch Drying Mode Continuous-Batch OperationPNEG-951 Dry Timer Operating Display Screens Main Display ScreenPNEG-951 Safety Circuit Shutdown Messages FAN and Heater Generated Errors Air Switch x StuckFan x Loss of Airflow Fan x No AirflowHousing x High Limit Grain Temp ShortGrain x Overheat Ignition FailureIllegal Flame Motor OverloadPlenum Temp Open Plenum Temp ShortINPUT/OUTPUT Generated Errors Vapor x High LimitAir System Failure Aux Load OverloadGrain Discharge Warning Load Motor OverloadMeter Rolls Failed Out of GrainMaster Display Generated Errors User SafetyCont-Batch Mode Chng Unload Motor OverloadNetwork Failed I/O Network Failed MastService and Maintanance Seasonal Inspection and Service Lubrication ProcedureFAN Blade Removal and Installation FAN Removaland Installation Heater Parts Removal and Installation FAN Motor RemovalMeter Roll Servicing Main ControlsHOW to Clear a Jammed Metering Roll Trouble Analysis Procedure PNEG-951 PNEG-951 PNEG-951 PNEG-951 Special Setup Screens AIR Switch Testing Meter Roll DisableMeter Roll Reverse Reverse time Select Unload MethodAttempt to Refill Select Dryer AddressModel Number Temperature Scale FAN/HEATER SelectPossible reasons for using On/Off burner SET Time & DateContrast Adjustment PNEG-951 Drying Charts Series Dryers Continuous Dry & Cool Staged Batch Continuous Full Heat Continuous Dry & Cool Staged Batch PNEG-951 Technical Reference Control Panel Jumper Wiring Control Panel Internal Wiring PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 Lower Control BOX Back Panelwiring Network FAN/HEATER Interface FAN Computer Pinouts FAN Control BOX Upper Terminal Strip Upper Back Panel Control Wiring 100 PNEG-951 PNEG-951 101 GSI Group, Inc 1004 E. Illinois St Assumption, IL Phone Fax