GSI Outdoors PNEG-951 manual Network Failed I/O, Network Failed Mast

Page 56

Network Failed I/O

This error is generated whenever Input/Output board (upper control panel) has lost its communications link with the master (lower control panel door) and the fan/heater boards. Check the blue and yellow wires marked N1-01 and N1-02 on a 3 terminal plug to make sure they are plugged in tightly. There are 3 LED lights next to this plug, one indicates power and the other two indicate data being transmitted. These two labeled RXD and TXD, should be flashing randomly back and forth indicating network activity.

Network Failed Mast

This error is generated whenever Master Display board (lower control panel) has lost its communications link with the Input/Output board (upper control panel door) and the fan/heater boards. Check the blue and yellow wires marked N1-01 and N1-02 on a 3 terminal plug to make sure they are plugged in tightly.

56

PNEG-951

Image 56

Contents 3 Module Network Portable Dryer Models Page Table of Contents Drying Charts Module Network Dryer Manual Introduction Section GSI GROUP, INC. Warranty Safety First Dryer Operation Decal DC-889 Decal DC-972 Decal DC-1227 Decal DC-973 USE Caution in the Operation of this Equipment PNEG-951 Control Panel Switch Panel Layout Control Power Switch Drying Mode SwitchLoad Auger Switch FAN SwitchMoisture Control Switch Outside Light SwitchRUN Switch Stop SwitchSetup Button Out of Grain Time Delay ButtonScreens Button Set Out of Grain View Grain Temps Meter Roll SP AvgUser Hour Meter Help Button DRY ButtonCool Button Unload ButtonStats Button PNEG-951 Dryer Pre Season Checks Electrical Power Inspect the Metering RollsRUN Button Fuel CheckLoad Auger Unload ONE Speed OperationUnload TWO Speed Operation Metering Roll OperationFAN Switches Burner SafetyBurner Test Fire Meter Roll 2 Speed DisplayDryer Shutdown Emergency Dryer ShutdownPNEG-951 Dryer Startup and Operation Initial Setup Parameters Timer and Delay SettingsFan and Auger Delays Dryer ShutdownLoad Delay OUT of Grain TMR position Unload Delay Setting Up The Temperature Set Points Drying mode switch is in the Continuous positionStartup Procedure StartupContinuous Flow Drying Mode Full Heat-Continuous Flow OperationDry and Cool-Continuous Flow Operation Staged Batch Drying Mode Continuous-Batch OperationPNEG-951 Dry Timer Operating Display Screens Main Display ScreenPNEG-951 Safety Circuit Shutdown Messages FAN and Heater Generated Errors Air Switch x StuckFan x Loss of Airflow Fan x No AirflowHousing x High Limit Grain Temp ShortGrain x Overheat Ignition FailureIllegal Flame Motor OverloadPlenum Temp Open Plenum Temp ShortINPUT/OUTPUT Generated Errors Vapor x High LimitAir System Failure Aux Load OverloadGrain Discharge Warning Load Motor OverloadMeter Rolls Failed Out of GrainMaster Display Generated Errors User SafetyCont-Batch Mode Chng Unload Motor OverloadNetwork Failed I/O Network Failed MastService and Maintanance Seasonal Inspection and Service Lubrication ProcedureFAN Blade Removal and Installation FAN Removaland Installation Heater Parts Removal and Installation FAN Motor RemovalMeter Roll Servicing Main ControlsHOW to Clear a Jammed Metering Roll Trouble Analysis Procedure PNEG-951 PNEG-951 PNEG-951 PNEG-951 Special Setup Screens Meter Roll Reverse Meter Roll DisableAIR Switch Testing Reverse time Select Unload MethodModel Number Select Dryer AddressAttempt to Refill Temperature Scale FAN/HEATER SelectPossible reasons for using On/Off burner SET Time & DateContrast Adjustment PNEG-951 Drying Charts Series Dryers Continuous Dry & Cool Staged Batch Continuous Full Heat Continuous Dry & Cool Staged Batch PNEG-951 Technical Reference Control Panel Jumper Wiring Control Panel Internal Wiring PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 Lower Control BOX Back Panelwiring Network FAN/HEATER Interface FAN Computer Pinouts FAN Control BOX Upper Terminal Strip Upper Back Panel Control Wiring 100 PNEG-951 PNEG-951 101 GSI Group, Inc 1004 E. Illinois St Assumption, IL Phone Fax