GSI Outdoors PNEG-951 manual Meter Roll Disable, AIR Switch Testing, Meter Roll Reverse

Page 70

By pressing and holding the button while the power is off. Continue to hold and turn on the control power for the dryer. You will be able to access certain dryer features that rarely need to be changed and if setup incorrectly, could cause your dryer not to operate properly or not at all.

Pressing will allow you to enter the customer setup screens in the following sequential order:

Meter Roll Disable

Disable Air Switches

Meter Roll Reverse Select

Select Unload Method

Select Dryer Address

Attempt to Refill

Model Number

Temperature Scale Select

Fan and Heater Select

Set Time & Date

Adjustable Grain High Limit

Note: To bypass any or all of these screens without changing the current settings just press .

METER ROLL DISABLE

This option allows you to shut off the monitoring of the meter roll sensor located in the rear of the dryer. This should be only used in the event of a failure of the sensor itself. This sensor is used for calculation of the bushel per hour, total bushels and meter roll rpm’s.

To toggle this feature on or off use the

buttons then press the

button to accept the

changes.

 

 

AIR SWITCH TESTING

This option allows you to disable the testing of the air switch. This is useful if you are doing a pre season check on your dryer and you want to start the fan and heater with no grain in the columns or you are having air switch problems. The computer will ignore the state of the air switch if you change the selection to NO.

To toggle this feature on or off use the

buttons then press the

button to accept the

changes.

 

 

Note: If the dryer’s control power is lost, this option will toggle back to its factory state of YES.

METER ROLL REVERSE

This feature allows the meter rolls to temporarily reverse themselves for a programmed amount of time to help remove any debris that may have built up around this area. This is very useful if you are drying grain with alot of trash. This will help prevent the grain from not moving in the grain columns then causing the dryer to shutdown with grain overheat error.

70

PNEG-951

Page 69 Page 71
Image 70
Page 69 Page 71
Contents 3 Module Network Portable Dryer Models Page Table of Contents Drying Charts Module Network Dryer Manual Introduction Section GSI GROUP, INC. Warranty Safety First Dryer Operation Decal DC-889 Decal DC-972 Decal DC-1227 Decal DC-973 USE Caution in the Operation of this Equipment PNEG-951 Control Panel Switch Panel Layout Load Auger Switch Control Power SwitchDrying Mode Switch FAN SwitchRUN Switch Moisture Control SwitchOutside Light Switch Stop SwitchSetup Button Screens Button Delay ButtonOut of Grain Time Set Out of Grain View Grain Temps Meter Roll SP AvgUser Hour Meter Cool Button Help ButtonDRY Button Unload ButtonStats Button PNEG-951 Dryer Pre Season Checks RUN Button Electrical PowerInspect the Metering Rolls Fuel CheckUnload TWO Speed Operation Load AugerUnload ONE Speed Operation Metering Roll OperationBurner Test Fire FAN SwitchesBurner Safety Meter Roll 2 Speed DisplayDryer Shutdown Emergency Dryer ShutdownPNEG-951 Dryer Startup and Operation Fan and Auger Delays Initial Setup ParametersTimer and Delay Settings Dryer ShutdownLoad Delay OUT of Grain TMR position Unload Delay Setting Up The Temperature Set Points Drying mode switch is in the Continuous positionStartup Procedure StartupContinuous Flow Drying Mode Full Heat-Continuous Flow OperationDry and Cool-Continuous Flow Operation Staged Batch Drying Mode Continuous-Batch OperationPNEG-951 Dry Timer Operating Display Screens Main Display ScreenPNEG-951 Safety Circuit Shutdown Messages Fan x Loss of Airflow FAN and Heater Generated ErrorsAir Switch x Stuck Fan x No AirflowGrain x Overheat Housing x High LimitGrain Temp Short Ignition FailurePlenum Temp Open Illegal FlameMotor Overload Plenum Temp ShortAir System Failure INPUT/OUTPUT Generated ErrorsVapor x High Limit Aux Load OverloadMeter Rolls Failed Grain Discharge WarningLoad Motor Overload Out of GrainCont-Batch Mode Chng Master Display Generated ErrorsUser Safety Unload Motor OverloadNetwork Failed I/O Network Failed MastService and Maintanance Seasonal Inspection and Service Lubrication ProcedureFAN Blade Removal and Installation FAN Removaland Installation Heater Parts Removal and Installation FAN Motor RemovalMeter Roll Servicing Main ControlsHOW to Clear a Jammed Metering Roll Trouble Analysis Procedure PNEG-951 PNEG-951 PNEG-951 PNEG-951 Special Setup Screens AIR Switch Testing Meter Roll DisableMeter Roll Reverse Reverse time Select Unload MethodAttempt to Refill Select Dryer AddressModel Number Temperature Scale FAN/HEATER SelectPossible reasons for using On/Off burner SET Time & DateContrast Adjustment PNEG-951 Drying Charts Series Dryers Continuous Dry & Cool Staged Batch Continuous Full Heat Continuous Dry & Cool Staged Batch PNEG-951 Technical Reference Control Panel Jumper Wiring Control Panel Internal Wiring PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 Lower Control BOX Back Panelwiring Network FAN/HEATER Interface FAN Computer Pinouts FAN Control BOX Upper Terminal Strip Upper Back Panel Control Wiring 100 PNEG-951 PNEG-951 101 GSI Group, Inc 1004 E. Illinois St Assumption, IL Phone Fax
Top Page Image Contents