GSI Outdoors PNEG-951 manual OUT of Grain TMR position

Page 38

3. Press the

button to adjust the settings.

4. Press the

button to accept the changes.

If you want to view the out of grain timer while the dryer is running, perform the following steps:

1. Press the

button the display will then show this selection screen:

2. Press the

to view the OUT OF GRAIN TIME selection screen.

3. Press the

button and move the pointer from the SET OUT OF GRAIN to the

OUT OF GRAIN TMR position.

4. Press the

to view the remaining time of the Out of Grain timer while the Load

Auger is running.

The TIME LEFT is a countdown of time from the Out of Grain timer setting you have entered above and will decrement if your fill auger is running and the Load Auger switch is in the AUTO position.

The LAST LOAD TIME is the amount of time the load or fill auger operated until the fill auger mercury switch was activated indicating the dryer is full.

NOTE: Anytime your TIME LEFT counter reaches zero, your dryer will shut down with a “Out of Grain” warning.

Fan Sequence Delay

The Fan Sequence Delay controls the amount of time between each fan startup to reduce the dryer startup amps. Default setting is 5 seconds.

To change the setting of this delay follow these instructions:

38

PNEG-951

Page 37 Page 39
Image 38
Page 37 Page 39
Contents 3 Module Network Portable Dryer Models Page Table of Contents Drying Charts Module Network Dryer Manual Introduction Section GSI GROUP, INC. Warranty Safety First Dryer Operation Decal DC-889 Decal DC-972 Decal DC-1227 Decal DC-973 USE Caution in the Operation of this Equipment PNEG-951 Control Panel Switch Panel Layout Load Auger Switch Control Power SwitchDrying Mode Switch FAN SwitchRUN Switch Moisture Control SwitchOutside Light Switch Stop SwitchSetup Button Out of Grain Time Delay ButtonScreens Button Set Out of Grain View Grain Temps Meter Roll SP AvgUser Hour Meter Cool Button Help ButtonDRY Button Unload ButtonStats Button PNEG-951 Dryer Pre Season Checks RUN Button Electrical PowerInspect the Metering Rolls Fuel CheckUnload TWO Speed Operation Load AugerUnload ONE Speed Operation Metering Roll OperationBurner Test Fire FAN SwitchesBurner Safety Meter Roll 2 Speed DisplayDryer Shutdown Emergency Dryer ShutdownPNEG-951 Dryer Startup and Operation Fan and Auger Delays Initial Setup ParametersTimer and Delay Settings Dryer ShutdownLoad Delay OUT of Grain TMR position Unload Delay Setting Up The Temperature Set Points Drying mode switch is in the Continuous positionStartup Procedure StartupContinuous Flow Drying Mode Full Heat-Continuous Flow OperationDry and Cool-Continuous Flow Operation Staged Batch Drying Mode Continuous-Batch OperationPNEG-951 Dry Timer Operating Display Screens Main Display ScreenPNEG-951 Safety Circuit Shutdown Messages Fan x Loss of Airflow FAN and Heater Generated ErrorsAir Switch x Stuck Fan x No AirflowGrain x Overheat Housing x High LimitGrain Temp Short Ignition FailurePlenum Temp Open Illegal FlameMotor Overload Plenum Temp ShortAir System Failure INPUT/OUTPUT Generated ErrorsVapor x High Limit Aux Load OverloadMeter Rolls Failed Grain Discharge WarningLoad Motor Overload Out of GrainCont-Batch Mode Chng Master Display Generated ErrorsUser Safety Unload Motor OverloadNetwork Failed I/O Network Failed MastService and Maintanance Seasonal Inspection and Service Lubrication ProcedureFAN Blade Removal and Installation FAN Removaland Installation Heater Parts Removal and Installation FAN Motor RemovalMeter Roll Servicing Main ControlsHOW to Clear a Jammed Metering Roll Trouble Analysis Procedure PNEG-951 PNEG-951 PNEG-951 PNEG-951 Special Setup Screens Meter Roll Reverse Meter Roll DisableAIR Switch Testing Reverse time Select Unload MethodModel Number Select Dryer AddressAttempt to Refill Temperature Scale FAN/HEATER SelectPossible reasons for using On/Off burner SET Time & DateContrast Adjustment PNEG-951 Drying Charts Series Dryers Continuous Dry & Cool Staged Batch Continuous Full Heat Continuous Dry & Cool Staged Batch PNEG-951 Technical Reference Control Panel Jumper Wiring Control Panel Internal Wiring PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 Lower Control BOX Back Panelwiring Network FAN/HEATER Interface FAN Computer Pinouts FAN Control BOX Upper Terminal Strip Upper Back Panel Control Wiring 100 PNEG-951 PNEG-951 101 GSI Group, Inc 1004 E. Illinois St Assumption, IL Phone Fax
Top Page Image Contents