Lincoln Electric IM613-B manual Status Light States CON’T

Page 30

B-11	OPERATION	B-11

STATUS LIGHT STATES (CON’T)

LED State	Power Source LED	LED on any other nodes (components);
		Wire Feeder, Control Box Etc.
Red LED blinking	Power source needs to be reprogrammed.	System component (node) needs to be
at a fast rate	Contact your Local Authorized Lincoln Field	reprogrammed. Contact your Local
	Service Facility.	Authorized Lincoln Field Service Facility.
Red LED ON and	Power source has a non-recoverable hard-	System component (node) has a non-recov-
steady	ware fault. Contact your Local Authorized	erable hardware fault. Contact your Local
	Lincoln Field Service Facility.	Authorized Lincoln Field Service Facility.

Green LED ON	System normal and functional.	System normal and functional.
and steady

Normal Blinking LED - Each illumination should exist for 0.5 seconds.

Fast Blinking LED - Each illumination should exist for 0.1 seconds.

POWER FEED 11

Image 30

Contents Safety Depends on You IM613-BSafety Electric Shock can kill Safety IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Section E Section FP315 Series Installation Power FeedHanging Safety PrecautionWire Feeder to Power Source Configurations On the FloorCable Connections Work Cable Connections Selecting the Proper Gear Ratio Wire Drive Gear Ratio High or LOW SpeedChanging the Wire Drive Ratio CurrentRatio Change Procedure DIP Switch Setup Setting DIP Switches in the Control BOXSetting DIP Switches in the Wire Drive Figure A.4Procedure to Install Drive Rolls and Guide Tubes Drive Roll KIT and Guide Tube InstallationFAST-MATEGUN Adapter Guide Tubes GUN Connection Guidelines GUN and Cable AssembliesMagnum Guns General GuidelinesCylinder may explode if damaged Gmaw Shielding GASLifting Handle Buildup of Shielding GAS may harm health or killGeneral Panel Installation Guidelines Optional Panels for Control BOXOperation Control Box Panels Lower Panels K1542-4 CV/Gouge PanelStdK1542-11 MX2 PanelOptional K1640-1 Dual Procedure / Memory Door Panel Optional K1542-12 MSP2 Panel OptionalControl BOX Panels -- SET UP Controls Description Control BOX -- PC Board AdjustmentsControl BOX -- Using Operating Limits Control BOX -- Setting Operating LimitsSTEP/4 Step Switch Wire Drive OperationWire Drive Settings -- External Cold Feed / GAS Purge SwitchElectrode Polarity Wire Reel Loading READI-REELS, Spools or CoilsWire Drive -- PC Board Adjustments Gear BOX RatioFeeding Electrode and Brake Adjustment GAS Guard Regulator SettingDrive Roll Pressure Setting Wire Reel Changing Wire Feed Overload ProtectionMaking a Weld Component Status Lights Status Light StatesStatus Light States CON’T Table C.1 Drive Roll and Guide Tube Kits AccessoriesWire Size Roll Drive Driven Solid Steel Electrode Cored ElectrodeGeneral Panel Installation Guidelines Description of Optional CON- Trol BOX PanelsK1543, K1544 and K1545 Input Cable Assemblies K659-1 GAS Guard Regulator Wire Spindle AdaptersK1536-1 Water Flow Sensor KIT K1649-1 Mounting Bracket HorizontalWire Drive Motor and Gearbox MaintenanceMaintenance Gun and Cable Maintenance1TROUBLESHOOTINGE-1 HOW to USE Troubleshooting GuideTroubleshooting Possible Cause Recommended Symptoms Course of Action Field Service FacilityYour local Lincoln Authorized Troubleshooting Possible Cause Course of ActionEither of these fail, the problem is Change Or harness disconnected from Fails the continuity test, repair or Possible Cause Err 004 Err 001Err 003 Err 005Err 200 Err 020Err 100 Err 201Err 211 Err 212Wiring Diagram Power Feed 11 Wire Feeder Diagrams Wiring DiagramL10834 Power Feed Basic Course $700.00Precaucion Warnung