Lincoln Electric IM613-B manual Change Or harness disconnected from

Page 41

E-7		TROUBLESHOOTING	E-7

	Observe all Safety Guidelines detailed throughout this manual
	PROBLEMS	POSSIBLE CAUSE	RECOMMENDED
	(SYMPTOMS)	POSSIBLE CAUSE	COURSE OF ACTION
	(SYMPTOMS)		COURSE OF ACTION

14. Displays and/or indicator lights		a. The encoders or switches may be	If all recommended possible areas of
do not change when their corre-		faulty.	misadjustment have been checked
sponding switches and or knobs			and the problem persists, Contact
are activated to request a		b. Check for broken harness wire(s)	your local Lincoln Authorized
change.		or harness disconnected from	Field Service Facility.
		intended location.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER FEED 11

Image 41

Contents IM613-B Safety Depends on YouSafety Electric Shock can kill Iii SafetySûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents P315 Series Section ESection F Power Feed InstallationWire Feeder to Power Source Configurations Safety PrecautionHanging On the FloorCable Connections Changing the Wire Drive Ratio Wire Drive Gear Ratio High or LOW SpeedWork Cable Connections Selecting the Proper Gear Ratio CurrentRatio Change Procedure Setting DIP Switches in the Control BOX DIP Switch SetupFigure A.4 Setting DIP Switches in the Wire DriveFAST-MATEGUN Adapter Guide Tubes Procedure to Install Drive Rolls and Guide TubesDrive Roll KIT and Guide Tube Installation Magnum Guns GUN and Cable AssembliesGUN Connection Guidelines General GuidelinesLifting Handle Gmaw Shielding GASCylinder may explode if damaged Buildup of Shielding GAS may harm health or killOptional Panels for Control BOX General Panel Installation GuidelinesOperation K1542-11 MX2 PanelOptional Control Box Panels Lower PanelsK1542-4 CV/Gouge PanelStd K1542-12 MSP2 Panel Optional K1640-1 Dual Procedure / Memory Door Panel OptionalControl BOX -- PC Board Adjustments Control BOX Panels -- SET UP Controls DescriptionControl BOX -- Setting Operating Limits Control BOX -- Using Operating LimitsWire Drive Settings -- External Wire Drive OperationSTEP/4 Step Switch Cold Feed / GAS Purge SwitchWire Drive -- PC Board Adjustments Wire Reel Loading READI-REELS, Spools or CoilsElectrode Polarity Gear BOX RatioDrive Roll Pressure Setting Feeding Electrode and Brake AdjustmentGAS Guard Regulator Setting Making a Weld Wire Reel ChangingWire Feed Overload Protection Status Light States Component Status LightsStatus Light States CON’T Wire Size Roll Drive Driven Solid Steel Electrode AccessoriesTable C.1 Drive Roll and Guide Tube Kits Cored ElectrodeK1543, K1544 and K1545 Input Cable Assemblies General Panel Installation GuidelinesDescription of Optional CON- Trol BOX Panels K1536-1 Water Flow Sensor KIT Wire Spindle AdaptersK659-1 GAS Guard Regulator K1649-1 Mounting Bracket HorizontalMaintenance MaintenanceWire Drive Motor and Gearbox Gun and Cable MaintenanceHOW to USE Troubleshooting Guide 1TROUBLESHOOTINGE-1Troubleshooting Your local Lincoln Authorized Possible Cause Recommended Symptoms Course of ActionField Service Facility Troubleshooting Course of Action Possible CauseEither of these fail, the problem is Change Or harness disconnected from Fails the continuity test, repair or Possible Cause Err 003 Err 001Err 004 Err 005Err 100 Err 020Err 200 Err 201Err 212 Err 211Wiring Diagram Power Feed 11 Wire Feeder Wiring Diagram DiagramsL10834 Power Feed $700.00 Basic CoursePrecaucion Warnung